Predicting the fiber orientation of reinforced molded components is required to improve their performance and safety. Continuum-based models for fiber orientation are computationally very efficient; however, they lack in a linked theory between fiber attrition, fiber–matrix separation and fiber alignment. This work, therefore, employs a particle level simulation which was used to simulate the fiber orientation evolution within a sliding plate rheometer. In the model, each fiber is accounted for and represented as a chain of linked rigid segments. Fibers experience hydrodynamic forces, elastic forces, and interaction forces. To validate this fundamental modeling approach, injection and compression molded reinforced polypropylene samples were subjected to a simple shear flow using a sliding plate rheometer. Microcomputed tomography was used to measure the orientation tensor up to 60 shear strain units. The fully characterized microstructure at zero shear strain was used to reproduce the initial conditions in the particle level simulation. Fibers were placed in a periodic boundary cell, and an idealized simple shear flow field was applied. The model showed a faster orientation evolution at the start of the shearing process. However, agreement with the steady-state aligned orientation for compression molded samples was found.
This study aims to use particle level simulation to simulate the breakage behavior of glass fibers subjected to simple shear flow. Each fiber is represented as a chain of rods that experience hydrodynamic, interaction, and elastic effects. In order to validate the approach of the model, the simulation results were compared to simple shear flow experiments conducted in a Couette Rheometer. The excluded volume force constants and critical fiber breakage curvature were tuned in the simulation to gain a better understanding of the system. Relaxation of the fiber clusters and a failure probability theory were introduced into the model to solve the fiber entanglement and thus, better fit the experimental behavior. The model showed agreement with the prediction on fiber length reduction in both number average length and weight average length. In addition, the simulation had a similar trend of breakage distribution compared to a loop test using glass fibers.
Long fiber-reinforced thermoplastics are an attractive design option for many industries due to their excellent mechanical properties and processability. Processing of these materials has a significant influence on their microstructure, which controls the properties of the final part. The microstructure is characterized by the fibers’ orientation, length, and concentration. Many characterization methods can capture the fiber orientation and concentration changes through the thickness in injection molded parts, but not the changes in fiber length. In this study, a technique for measuring fiber length in the core and shell regions of molded parts was proposed, experimentally verified, and used on injection molded 20 wt.% glass fiber-reinforced polypropylene plaques. The measured fiber length in the core was 50% higher than in the shell region. Comparison with simulation results shows disagreement in the shape of the through-thickness fiber length profile. Stiffness predictions show that the through-thickness changes in fiber length have little impact on the longitudinal and transverse Young’s modulus.
Understanding the mechanics of fiber attrition during the extrusion process is highly important in predicting the strength of long fiber-reinforced thermoplastic composites. However, little work has been done to investigate the mechanics of fiber dispersion and its effects on fiber attrition. This study aims at investigating fiber dispersion in simple shear flows for long fiber-reinforced thermoplastic pellets. Depending on the fabrication process, fiber bundles display distinct levels of compaction within the pellets. Studies have shown that morphological differences can lead to differences in dispersion mechanics; therefore, using a Couette rheometer and a sliding plate rheometer, coated and pultruded pellets were subjected to simple shear deformation, and the amount of dispersion was quantified. Additionally, a new image-based analysis method is presented in this study to measure fiber dispersion for a multi-pellet-filled system. Results from the single-pellet dispersion study showed a small amount of correlation between the dimensionless morphological parameter and the dispersion measurement. Pultruded and coated pellets were both found to have similar dispersion rates in a multi-pellet system. However, pultruded pellets were found to have a higher dispersion value at all levels when compared with coated pellets in both dispersion studies.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.