Electrochemical energy storage is one of the main societal challenges of this century. The performances of classical lithium-ion technology based on liquid electrolytes have made great advances in the past two decades, but the intrinsic instability of liquid electrolytes results in safety issues. Solid polymer electrolytes would be a perfect solution to those safety issues, miniaturization and enhancement of energy density. However, as in liquids, the fraction of charge carried by lithium ions is small (<20%), limiting the power performances. Solid polymer electrolytes operate at 80 °C, resulting in poor mechanical properties and a limited electrochemical stability window. Here we describe a multifunctional single-ion polymer electrolyte based on polyanionic block copolymers comprising polystyrene segments. It overcomes most of the above limitations, with a lithium-ion transport number close to unity, excellent mechanical properties and an electrochemical stability window spanning 5 V versus Li(+)/Li. A prototype battery using this polyelectrolyte outperforms a conventional battery based on a polymer electrolyte.

International audienceCu2+-doped zeolitic imidazolate framework (ZIF) crystals were efficiently prepared by reaction of Cu(NO3)2, Zn(NO3)2, and 2-methylimidazole in methanol at room temperature. Scanning electron microscopy, transmission electron microscopy and X-ray diffraction showed that the Cu/ZIF-8 particles were nanosized (between ca. 120 and 170 nm) and that the body-centered cubic crystal lattice of the parent ZIF-8 framework is continuously maintained, regardless of the doping percentage. Moreover, thermogravimetric analyses and specific BET surface area measurements demonstrated that the doping does not alter the high stability of ZIF-8 crystals and that the porosity only decreases at a high doping percentage (25% in Cu2+). The Cu/ZIF-8 material showed excellent catalytic activity in the [3 + 2] cycloaddition of organic azides with alkynes and in Friedländer and Combes condensations due to the high catalyst surface area and the high dispersion of Cu/ZIF-8 particles. Notably, the Cu/ZIF-8 particles not only exhibit excellent performance but also show great stability in the reaction, allowing their reuse up to ten times in condensation reactions. Our findings explored a simple and powerful way to incorporate metal ions into the backbones of open framework materials without losing their properties

A new path for the design of safe and effi cient, all-solid-state Li-ion batteries by spark plasma sintering (SPS) is considered. To reach a good electrochemical performance from such batteries, several parameters are investigated, such as the composite-electrode formulation (active material/electrolyte/ carbon ratio) and the infl uence of the sintering parameters on their compactness. The formulation is optimized to ensure good ionic and electronic percolation through the composite electrode's volume. The compactness has to be suffi cient to guarantee a good mechanical aspect, while the residual porosity in the composite electrode allows electrode-volume changes upon insertion and deinsertion, preserving the electrode/electrolyte interfaces, which are crucial in such technology. Based on these investigations, an all-solid-state battery with a surface capacity of 2.2 mA h cm − 2 is assembled by SPS, displaying a promising electrochemical performance at 80 ° C.

In this work, we report the solvothermal synthesis of Ce-doped YAG (YAG:Ce) nanoparticles (NPs) and their association with a free-Cd CuInS2/ZnS (CIS/ZnS) core/shell QDs for application into white light emitting diode (WLED). 1500 °C-annealed YAG:Ce NPs and CIS/ZnS core/shell QDs exhibited intense yellow and red emissions band with maxima at 545 and 667 nm, respectively. Both YAG:Ce nanophosphor and CIS/ZnS QDs showed high photoluminescence quantum yield (PL QY) of about 50% upon 460 nm excitation. YAG:Ce nanophosphor layer and bilayered YAG:Ce nanophosphor-CIS/ZnS QDs were applied on blue InGaN chip as converter wavelength to achieve WLED. While YAG:Ce nanophosphor converter layer showed low color rendering index (CRI) and cold white light, bilayered YAG:Ce nanophosphor-CIS/ZnS QDs displayed higher CRI of about 84 and warm white light with a correlated color temperature (CCT) of 2784 K. WLED characteristics were measured as a function of forward current from 20 to 1200 mA. The white light stability of bilayered nanophosphor-QDs-based WLED operated at 200 mA was also studied as a function of operating time up to 40 h. Interestingly, CRI and CCT of such device tend to remain constant after 7 h of operating time suggesting that layer-by-layer structure of YAG:Ce phosphor and red-emitting CIS/ZnS QDs could be a good solution to achieve stable warm WLED, especially when high current density is applied.

Relatively monodisperse and highly luminescent Mn(2+)-doped zinc blende ZnSe nanocrystals were synthesized in aqueous solution at 100 °C using the nucleation-doping strategy. The effects of the experimental conditions and of the ligand on the synthesis of nanocrystals were investigated systematically. It was found that there were significant effects of molar ratio of precursors and heating time on the optical properties of ZnSe:Mn nanocrystals. Using 3-mercaptopropionic acid as capping ligand afforded 3.1 nm wide ZnSe:Mn quantum dots (QDs) with very low surface defect density and which exhibited the Mn(2+)-related orange luminescence. The post-preparative introduction of a ZnS shell at the surface of the Mn(2+)-doped ZnSe QDs improved their photoluminescence properties, resulting in stronger emission. A 2.5-fold increase in photoluminescence quantum yield (from 3.5 to 9%) and of Mn(2+) ion emission lifetime (from 0.62 to 1.39 ms) have been observed after surface passivation. The size and the structure of these QDs were also corroborated by using transmission electron microscopy, energy dispersive spectroscopy, and X-ray powder diffraction.

Luminescent ZnO nanocrystals were synthesized by basic hydrolysis of Zn(OAc)(2) in the presence of oleic acid and then functionalized with (poly)aminotrimethoxysilanes in the presence of tetramethylammonium hydroxide to render the QDs water-dispersible. The highest photoluminescence quantum yield (17%) was achieved using N(1)-(2-aminoethyl)-N(2)-[3-(trimethoxysilyl)propyl]-1,2-ethanediamine as surface ligand. Transmission electron microscopy and powder x-ray diffraction showed highly crystalline materials with a ZnO nanoparticle diameter of about 4 nm. The cytotoxicity of the different siloxane-capped ZnO QDs towards growing Escherichia coli bacterial cells was evaluated in MOPS-minimal medium. Although concentrations of 5 mM in QDs caused a complete growth arrest in E. coli, siloxane-capped ZnO QDs appeared weakly toxic at lower doses (0.5 or 1 mM). The concentration of bioavailable Zn (2+) ions leaked from ZnO QDs was evaluated using the biosensor bacteria Cupriavidus metallidurans AE1433. The results obtained clearly demonstrate that concentrations of bioavailable Zn(2+) are too low to explain the inhibitory effects of the ZnO QDs against bacteria cells at 1 mM and that the siloxane shell prevents ZnO QDs from dissolution contrary to uncapped ZnO nanoparticles. Because of their low cytotoxicity, good biocompatibility, low cost and large number of functional amine end groups, which makes them easy to tailor for end-user purposes, siloxane-capped ZnO QDs offer a high potential as fluorescent probes and as biosensors.

Water-dispersible CdS quantum dots (QDs) emitting from 510 to 650 nm were synthesized in a simple one-pot noninjection hydrothermal route using cadmium chloride, thiourea, and 3-mercaptopropionic acid (MPA) as starting materials. All these chemicals were loaded at room temperature in a Teflon sealed tube and the reaction mixture heated at 100 °C. The effects of CdCl(2)/thiourea/MPA feed molar ratios, pH, and concentrations of precursors affecting the growth of the CdS QDs, was monitored via the temporal evolution of the optical properties of the CdS nanocrystals. High concentration of precursors and high MPA/Cd feed molar ratios were found to lead to an increase in the diameter of the resulting CdS nanocrystals and of the trap state emission of the dots. The combination of moderate pH value, low concentration of precursors and slow growth rate plays the crucial role in the good optical properties of the obtained CdS nanocrystals. The highest photoluminescence achieved for CdS@MPA QDs of average size 3.5 nm was 20%. As prepared colloids show rather narrow particle size distribution, although all reactants were mixed at room temperature. CdS@MPA QDs were characterized by UV-vis and photoluminescence spectroscopy, powder X-ray diffraction, transmission electron microscopy, energy-dispersive X-ray spectrometry and MALDI TOF mass spectrometry. This noninjection one-pot approach features easy handling and large-scale production with excellent synthetic reproducibility. Surface passivation of CdS@MPA cores by a wider bandgap material, ZnS, led to enhanced luminescence intensity. CdS@MPA and CdS/ZnS@MPA QDs exhibit high photochemical stability and hold a good potential to be applied in optoelectronic devices and biological applications.

International audienceWater-dispersible 1-thioglycerol-capped Mn-doped ZnSe quantum dots (QDs) were prepared in aqueous solution through the nucleation-doping method by using safe and low-cost inorganic salts as precursors. Influence of the Zn/Se ratio, precursors concentrations and reaction pH on the particle size, colloidal stability, and photoluminescence (PL) were investigated. Under optimal conditions, thioglycerol-capped ZnSe:Mn QDs with an average diameter of 3.5 nm and a PL quantum yield of 3.5% in water at neutral pH were produced. X-ray powder diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, UV- visible spectroscopy and spectrofluorometry have been used to characterize the crystal structure and the optical properties of the dots. Remarkable improvements of stability in biological medium and PL were achieved by introduction of a ZnO shell through basic hydrolysis of Zn(NO3)2. ZnO was found to eliminate the surface-trap state fromMn2+-doped ZnSe cores and enhance their PL quantum yield to 12%. Growth inhibition tests showed that core/shell ZnSe:Mn/ZnO@TG QDs do not exhibit any cytotoxicity toward E. coli bacterial cells up to a concentration of 0.14 mg/mL, indicating that these nanocrystals can be considered as building blocks for the synthesis of bioprobes for cells and tissues imaging