Recently, gas-lubricated bearings have drawn enormous attention for clean energy conversion/process systems such as fuel cells, micro-gas-turbines, gas compressors, etc. Among many different types of gas bearings, tilting pad gas bearings have many attractive features such as high rotor-bearing stability and less severe thermal issues (due to multipad configurations) than foil gas bearings. However, extension of the application of the tilting pad gas bearings to flexible rotors and harsh environments with external vibrations/impacts poses significant design challenges. The design problem addressed in this paper is the vibration damper to be integrated with the flexure pivot tilting pad gas bearing (FPTPGB) with and without pad radial compliance. Linear and nonlinear dynamic models of the FPTPGB with vibration damper were developed, and rotordynamic performance was evaluated to prescribe design guidelines for the selection of bearing shell mass and damper properties. Direct numerical integration (time-domain orbit simulations) and linear analyses were employed to predict rotordynamic responses and other interesting behaviors relevant of rotor-bearing systems with the vibration damper. Rotor-bearing systems showed better performance with larger damper stiffness for both with and without radial compliance. However, bearing shell mass showed different tendencies; lower bearing shell mass was shown to be ideal for bearings with radial compliance, while the opposite trend was observed for bearings without radial compliance. Although increasing the degrees of freedom of the system by allowing the bearing shell to move introduces additional natural frequencies, careful design considerations could allow the placement of the natural frequencies outside of the operating range.
No abstract
No abstract
Tie bolt rotors for centrifugal compressors comprise multiple shaft components that are held together by a single tie bolt. The axial connections of these rotors—including butt joints, Hirth couplings, and Curvic couplings—exhibit a contact stiffness effect, which tends to lower the shaft bending frequencies compared to geometrically identical monolithic shafts. If not accounted for in the design stage, shaft bending critical speed margins can be compromised after a rotor is built. A previous paper had investigated the effect of tie bolt force on the bending stiffness of stacked rotor assemblies with butt joint interfaces, both with and without pilot fits. This previous work derived an empirical contact stiffness model and developed a practical finite element modeling approach for simulating the axial contact surfaces, which was validated by predicting natural frequencies for several test rotor configurations. The present work built on these previous results by implementing the same contact stiffness modeling approach on a real tie bolt rotor system designed for a high pressure centrifugal compressor application. Each joint location included two axial contact faces, with contact pressures up to five times higher than previously modeled, and a locating pilot fit. The free-free natural frequencies for different amounts of tie bolt preload force were measured, and the frequencies exhibited the expected stiffening behavior with increasing preload. However, a discontinuity in the data trend indicated a step-change increase in the contact stiffness. It was shown that this was likely due to one or more of the contact faces becoming fully engaged only after sufficient tie bolt force was applied. Finally, a design calculation was presented that can be used to estimate whether contact stiffness effects may be ignored, which could simplify rotor analyses if adequate contact pressure is used.
This paper introduces a design and manufacturing of mesoscale flexure pivot tilting pad gas bearing with a diameter of 5 mm and a length of 1–2.5 mm for PowerMEMS (micro electromechanical systems for power generation) applications with power ranges of 100–200 W. Potential applications include power source for unmanned air vehicles, small robots, microgas turbines to be harnessed by very small solid oxide fuel cells, microblowers/compressors for microfuel cells, etc. The design studies involve scaling analysis, time-domain orbit simulations for stability analyses, and frequency-domain modal analyses for prediction of rotor-bearing natural frequencies. Scaling analysis indicates that direct miniaturization of macroscale tilting pad gas bearing can result in a large bearing number, which may render the rotor-bearing system unstable. However, the scaling analysis provides the baseline design from which the final design can be derived considering manufacturing issue. The generalized modal analysis using impedance contours predict damped natural frequencies close to those from orbit simulations, providing high fidelity to the developed numerical methods. It was predicted that the designed mesoscale tilting pad gas bearings would show very stable operation up to a maximum simulated speed of 1,000,000 rpm. The designed mesoscale tilting pad gas bearings were manufactured using X-ray lithography and electroplating.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.