Aim To assess the suitability of several 3D‐printed resins for the manufacturing of tooth replicas for endodontic training in comparison with commercially available replicas by analysing the properties of the materials and comparing them with real teeth during endodontic training. Methodology Tooth replicas were 3D‐printed using four resins (NextDent Model, NextDent C&B, V‐Print ee and Vero White Plus) and compared with two commercially available products (VDW and Smile Factory) as well as extracted human teeth. Martens hardness, indentation modulus and radiopacity were investigated on these tooth replicas. Experienced dentists evaluated the suitability of the replicas for endodontic training by comparing them with real teeth in terms of appearance, anatomy, radiopacity, similarity to dentine during access opening, canal gauging and canal instrumentation. Data were analysed using the Kolmogorov–Smirnov and Mann–Whitney U‐test. Results The greatest hardness values were recorded for human dentine (P < 0.001), followed by V‐Print ee and the commercial tooth replica of Smile Factory. The greatest radiopacity was associated with VOC and dentine (P < 0.001) in comparison with the other materials tested. The appearance of the in‐house printed tooth replicas was subjectively evaluated by the dentists as being more realistic than the commercially available products. No differences between the replicas was detected during mechanical instrumentation of root canals. Conclusion None of the tooth replicas were able to simulate human dentine from the perspectives evaluated. V‐Print ee had radiopacity comparable with dentine, but its hardness was not comparable with dentine.
SUMMARY Objectives Modern adhesives and composites allow the restoration of deep defects. In such cases, the matrix technique is particularly challenging, and excess composite is a common problem. Removing such overhangs with a scalpel has already been described as a substance preserving or selective finishing technique. Clinically, restoration margins may appear as a white line after scalpel finishing, and it is unclear whether this line represents a marginal gap and/or whether scalpel finishing promotes marginal gap formation. Therefore, the aim of this study was to investigate the influence of scalpel finishing of deep Class II composite restorations on marginal gap formation. Methods and Materials Standardized mesioocclusal-distal (MOD) cavities were prepared and restored in 60 human molars randomly divided into six finishing protocol groups: G1, scalpels (SC); G2, oscillating files (OF); G3, finishing strips (FS); G4, scalpels and finishing strips (SC+FS); G5, scalpels and polishing discs (SC+PD); G6, polishing discs alone (PD, controls). The groups were additionally assigned to finishing and polishing in a phantom head (groups 1–4) or hand-held setting (groups 5–6) to simulate clinical and in-vitro research conditions, respectively. After restoration, artificial aging was performed by thermocycling (5–55°C, 2500 cycles) and mechanical loading (50 newtons (N) with 500,000 cycles) prior to scanning electron microscopy analysis of proximal restoration margin quality on the mesial and distal surfaces (n=120) of each tooth. Outcomes (perfect margin, marginal gap, overhang, marginal fracture) were statistically analyzed by t-test, Mann-Whitney U test, single-factor analysis of variance, post-hoc t-test, Kruskal-Wallis test and Dunn-Bonferroni correction for multiple group comparisons. Cohen’s effect size d(Cohen) was calculated to show the strength of the relationship between variables. Results Overall, marginal quality was significantly better in the hand-held setting (SC+PD and PD) than the phantom head setting (SC, OF, FS, SC+FS). The best marginal quality was achieved with oscillating files in the phantom head setting and with scalpels plus polishing discs in the hand-held setting. Marginal gaps occurred significantly more often with scalpels, but the proportion of gaps was very low and clinically insignificant. Finishing strips were the least effective instruments for removing overhangs but performed better in combination with scalpels. Conclusions Scalpel finishing can effectively and gently remove overhangs from enamel. However, blades should be used with caution as they can cut the dentin and cementum. Scalpel finishing does not lead to a clinically relevant increase in marginal gaps, but should be followed by polishing, whenever possible, to eliminate any marginal fractures that might be present.
Background: The clinical management of teeth with complex dens invaginatus (DI) malformations and apical periodontitis may be challenging due to the lack of routine. The aim of this case report is to describe the endodontic treatment of an immature tooth with DI and to discuss strategies for preclinical training for teeth with such malformations. Case report: A 9-year-old male presented with an immature maxillary incisor with DI (Oehlers Type II) and apical periodontitis which was diagnosed by cone beam computed tomography (CBCT). Revitalization was initially attempted but then abandoned after failure to generate a stable blood clot. Nevertheless, considerable increase in both root length and thickness could be detected after medication with calcium hydroxide followed by root canal filling with MTA as an apical plug. Conclusions: The endodontic management of teeth with DI requires thorough treatment planning. In immature teeth, under certain conditions, root maturation may occur even with conventional apexification procedures. From an educational perspective, different strategies including CBCT and 3D-printed transparent tooth models for visualization of the complex internal morphology and redesigned 3D-printed replica with various degrees of difficulty for endodontic training, can be used to overcome the challenges associated with endodontic treatment of such teeth.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.