The article discusses an approach based on the analysis of the drive motor currents to create an additional means of protection against emergency situations during the operation of bridge cranes associated with lifting a load with a mass exceeding the permissible one. A mathematical model of an overhead crane drive is described, as well as the results of computer simulation. It is shown that in the process of lifting up, before the stage of lifting the load, the stator current of the drive electric motor does not depend of the load mass, but when the load is detached, already for several periods of the mains voltage after the rope is pulled, when the mass of the load is exceeded, a measurable excess of the amplitude value of the current is recorded. This pattern has been confirmed for a number of cranes of various lifting capacities used at metallurgical enterprises. The possibility of diagnosing excess weight of the lifted load with a higher speed than existing mechanical methods of overload control is demonstrated, at the same time it is not required to make changes to the structural elements of overhead cranes.
Аннотация. Выполнена сравнительная оценка термических напряжений в объеме железорудных окатышей с дифференцированной порис-тостью. Проанализировано термонапряженное состояние окатышей, полученных с применением технологии теплосилового напыления влажной шихты на шихтовый гарнисаж и на комкуемые материалы. Установлено влияние пористости, термической массивности окаты-шей на величину и характер изменения (распределения) термических напряжений по сечению окатышей. Оценен характер изменения прочности окатышей с дифференцированной пористостью по его сечению с динамикой температурного поля пористой сферы и крите-риями термической массивности в зародыше и оболочке окатыша. Проведен анализ роли термических напряжений в активации режима спекания железорудных окатышей, предложены рекомендации по совершенствованию теплового режима обжига окатышей. На основе этого анализа сделан вывод о более благоприятной поровой структуре полученных по технологии принудительного зародышеобразования окатышей, в объеме которых сформирован зародыш с повышенной пористостью.Ключевые слова: термонапряженное состояние, дифференцированная пористость, характер изменения прочности, температурное поле порис-той сферы, интенсивность нагрева, принудительное зародышеобразование, напыление влажной шихты, зародыши, оболочка, железоруд-ные окатыши.
Сибирский государственный индустриальный университет (654007, Россия, Новокузнецк, Кемеровская обл., ул. Кирова, 42) Аннотация. Рассмотрены особенности движения зародыша сложной формы на тарельчатом окомкователе в производстве железорудных окатышей. В результате проведенного анализ сил, действующих на кубический зародыш при его перекате на шихтовом гарнисаже (ШГ) в условиях пластической деформации, построена математическая модель, позволяющая определить оптимальные параметры работы окомкователя для производства окатышей по технологии принудительного зародышеобразования. Рассмотрены два частных случая устойчивос ти зародыша на ШГ окомкователя и условия преодоления устойчивости, связанные с формированием переката. Устойчивость зародыша или, напротив, его перекат определяются горизонтальным положением его центра массы относительно опорного ребра, расположенного поперек вероятного направления переката. Если линия действующей силы (силы тяжести) переместится за опорное ребро и опорную плоскость, то сформируется момент силы, который выведет зародыш из состояния устойчивости и сформирует перекат зародыша. Первым частным случаем устойчивости зародыша на наклонной плоскости является отсутствие переката на ШГ при минимальной величине центробежной силы, что соответствует расположению зародыша в центральных областях зоны окомкователя, или работе рабочего органа с низкой частотой вращения (n < 3 об/мин). Более общим случаем выхода зародыша из состояния устойчивости в режим переката на наклонной плоскости ШГ является работа окомкователя при сравнительно высокой величине центробежной силы (n >3 об/мин) и расположение зародыша в периферийных областях рабочей зоны окомкователя. Для указанных случаев сформулированы условия переката зародышей на ШГ в рабочей зоне окомкователя и корректирующие мероприятия в условиях пластической деформации при смятии его углов и ребер. Показаны особенности движения зародыша в рабочей зоне тарели окомкователя. Отмечены условия для корректировки режима принудительного зародышеобразования и озвучены мероприятия по целенаправленному воздействию на коэффициент смятия зародыша. Установлено, что для организации режима переката зародыша сложной формы угол наклона тарели окомкователя к горизонту следует назначать в зависимости от частоты его вращения и коэффициента смятия зародышей.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.