The pathological changes in osteoarthritis--a degenerative joint disease prevalent among older people--start at the molecular scale and spread to the higher levels of the architecture of articular cartilage to cause progressive and irreversible structural and functional damage. At present, there are no treatments to cure or attenuate the degradation of cartilage. Early detection and the ability to monitor the progression of osteoarthritis are therefore important for developing effective therapies. Here, we show that indentation-type atomic force microscopy can monitor age-related morphological and biomechanical changes in the hips of normal and osteoarthritic mice. Early damage in the cartilage of osteoarthritic patients undergoing hip or knee replacements could similarly be detected using this method. Changes due to aging and osteoarthritis are clearly depicted at the nanometre scale well before morphological changes can be observed using current diagnostic methods. Indentation-type atomic force microscopy may potentially be developed into a minimally invasive arthroscopic tool to diagnose the early onset of osteoarthritis in situ.

Cartilage stiffness was measured ex vivo at the micrometer and nanometer scales to explore structure-mechanical property relationships at smaller scales than has been done previously. A method was developed to measure the dynamic elastic modulus, |E(*)|, in compression by indentation-type atomic force microscopy (IT AFM). Spherical indenter tips (radius = approximately 2.5 microm) and sharp pyramidal tips (radius = approximately 20 nm) were employed to probe micrometer-scale and nanometer-scale response, respectively. |E(*)| values were obtained at 3 Hz from 1024 unloading response curves recorded at a given location on subsurface cartilage from porcine femoral condyles. With the microsphere tips, the average modulus was approximately 2.6 MPa, in agreement with available millimeter-scale data, whereas with the sharp pyramidal tips, it was typically 100-fold lower. In contrast to cartilage, measurements made on agarose gels, a much more molecularly amorphous biomaterial, resulted in the same average modulus for both indentation tips. From results of AFM imaging of cartilage, the micrometer-scale spherical tips resolved no fine structure except some chondrocytes, whereas the nanometer-scale pyramidal tips resolved individual collagen fibers and their 67-nm axial repeat distance. These results suggest that the spherical AFM tip is large enough to measure the aggregate dynamic elastic modulus of cartilage, whereas the sharp AFM tip depicts the elastic properties of its fine structure. Additional measurements of cartilage stiffness following enzyme action revealed that elastase digestion of the collagen moiety lowered the modulus at the micrometer scale. In contrast, digestion of the proteoglycans moiety by cathepsin D had little effect on |E(*)| at the micrometer scale, but yielded a clear stiffening at the nanometer scale. Thus, cartilage compressive stiffness is different at the nanometer scale compared to the overall structural stiffness measured at the micrometer and larger scales because of the fine nanometer-scale structure, and enzyme-induced structural changes can affect this scale-dependent stiffness differently.

Bioabsorbable polymer implants may provide a viable alternative to metal implants for internal fracture fixation. One of the potential difficulties with absorbable implants is the possible toxicity of the polymeric degradation products especially if they accumulate and become concentrated. Accordingly, material evaluation must involve dose-response toxicity data as well as mechanical properties and degradation rates. In this study the toxicity and rates of degradation for six polymers were determined, along with the toxicity of their degradation product components. The polymers studied were poly(glycolic acid) (PGA), two samples of poly(L-lactic acid) (PLA) having different molecular weights, poly(ortho ester) (POE), poly(epsilon-caprolactone) (PCL), and poly(hydroxy butyrate valerate) (5% valerate) (PHBV). Polymeric specimens were incubated at 37 degrees C in 0.05 M Tris buffer (pH 7.4 at 37 degrees C) and sterile deionized water. The solutions were not changed during the incubation intervals, providing a worst-case model of the effects of accumulation of degradation products. The pH and acute toxicity of the incubation solutions and the mass loss and logarithmic viscosity number of the polymer samples were measured at 10 days, 4, 8, 12, and 16 weeks. Toxicity was measured using a bioluminescent bacteria, acute toxicity assay system. The acute toxicity of pure PGA, PLA, POE, and PCL degradation product components was also determined. Degradation products for PHBV were not tested. PGA incubation solutions were toxic at 10 days and at all following intervals. The lower molecular weight PLA incubation solutions were not toxic in buffer but were toxic by 4 weeks in water.(ABSTRACT TRUNCATED AT 250 WORDS)

The mechanical properties of biodegradable polymers and composites proposed for use in internal fixation (in place of stainless steel) are crucial to the performance of devices made from them for support of healing bone. To assess the reported range of properties and degradation rates, we searched and reviewed papers and abstracts published in English from 1980 through 1988. Mechanical property data were found for poly(lactic acid), poly(glycolic acid), poly(epsilon-caprolactone), polydioxanone, poly(ortho ester), poly(ethylene oxide), and/or their copolymers. Reports of composites based on several of these materials, reinforced with nondegradable and degradable fibers, were also found. The largest group of studies involved poly(lactic acid). Mechanical test methods varied widely, and studies of the degradation of mechanical properties were performed under a variety of conditions, mostly in vitro rather than in vivo. Compared to annealed stainless steel, unreinforced biodegradable polymers were initially up to 36% as strong in tension and 54% in bending, but only about 3% as stiff in either test mode. With fiber reinforcement, reported highest initial strengths exceeded that of stainless steel. Stiffness reached 62% of stainless steel with nondegradable carbon fibers, 15% with degradable inorganic fibers, but only 5% with degradable polymeric fibers. The slowest-degrading unreinforced biodegradable polymers were poly(L-lactic acid) and poly(ortho ester). Biodegradable composites with carbon or inorganic fibers generally lost strength rapidly, with a slower loss of stiffness, suggesting the difficulty of fiber-matrix coupling in these systems. The strength of composites reinforced with (lower modulus) degradable polymeric fibers decreased more slowly. Low implant stiffness might be expected to allow too much bone motion for satisfactory healing. However, unreinforced or degradable polymeric fiber reinforced materials have been used successfully clinically. The key has been careful selection of applications, plus use of designs and fixation methods distinctly different from those appropriate for stainless steel devices.

Isothermal calorimetry measures the heat flow of biological processes, which is proportional to the rate at which a given chemical or physical process takes place. Modern isothermal microcalorimeters make measurements of less than a microwatt of heat flow possible. As a result, as few as 10 000-100 000 active bacterial cells in culture are sufficient to produce a real-time signal dynamically related to the number of cells present and their activity. Specimens containing bacteria need little preparation, and isothermal microcalorimetry (IMC) is a nondestructive method. After IMC measurements, the undisturbed samples can be evaluated by any other means desired. In this review, we present a basic description of microcalorimetry and examples of microbiological applications of IMC for medical and environmental microbiology. In both fields, IMC has been used to quantify microbial activity over periods of hours or even days. Finally, the recent development of highly parallel instruments (up to 48 channels) and the constantly decreasing costs of equipment have made IMC increasingly attractive for microbiology. Miniaturization of isothermal calorimeters provides an even wider range of possibilities.

As documented previously, articular cartilage exhibits a scale-dependent dynamic stiffness when probed by indentation-type atomic force microscopy (IT-AFM). In this study, a micrometer-size spherical tip revealed an unimodal stiffness distribution (which we refer to as microstiffness), whereas probing articular cartilage with a nanometer-size pyramidal tip resulted in a bimodal nanostiffness distribution. We concluded that indentation of the cartilage's soft proteoglycan (PG) gel gave rise to the lower nanostiffness peak, whereas deformation of its collagen fibrils yielded the higher nanostiffness peak. To test our hypothesis, we produced a gel-microfiber composite consisting of a chondroitin sulfate-containing agarose gel and a fibrillar poly(ethylene glycol)-terephthalate/poly(butylene)-terephthalate block copolymer. In striking analogy to articular cartilage, the microstiffness distribution of the synthetic composite was unimodal, whereas its nanostiffness exhibited a bimodal distribution. Also, similar to the case with cartilage, addition of the negatively charged chondroitin sulfate rendered the gel-microfiber composite's water content responsive to salt. When the ionic strength of the surrounding buffer solution increased from 0.15 to 2 M NaCl, the cartilage's microstiffness increased by 21%, whereas that of the synthetic biomaterial went up by 31%. When the nanostiffness was measured after the ionic strength was raised by the same amount, the cartilage's lower peak increased by 28%, whereas that of the synthetic biomaterial went up by 34%. Of interest, the higher peak values remained unchanged for both materials. Taken together, these results demonstrate that the nanoscale lower peak is a measure of the soft PG gel, and the nanoscale higher peak measures collagen fibril stiffness. In contrast, the micrometer-scale measurements fail to resolve separate stiffness values for the PG and collagen fibril moieties. Therefore, we propose to use nanostiffness as a new biomarker to analyze structure-function relationships in normal, diseased, and engineered cartilage.

No abstract

Based on the molecular stent concept, a series of tough double-network hydrogels (St-DN gels) made from the components of proteoglycan aggregates - chondroitin sulfate proteoglycans (1), chondroitin sulfate (2), and sodium hyaluronate (3) - are successfully developed in combination with a neutral biocompatible polymer. This work demonstrates a promising method to create biopolymer-based tough hydrogels for biomedical applications.