This study focuses waterproof-breathable fabric development by applying electrospun web of polyurethane (PU), PAN, and PES directly onto the substrate fabric. Advantages of textile fabrics of elastomeric nanofibrous membranes over gortex specimen are the mass production feasibility, high elastomeric properties, more body comfort parameters, and fabric production without holes and needle traces formation. In this work, we identified the PU nanofibrous membrane as the best and useful web for application in waterproof-breathable fabrics. Air permeability, water vapor transport rate, and resistance to water penetration average value for the prepared PU fibers web (sample of S1) were about 10 ml/s, 430 g/m 2 /24 h, 15 cm H 2 O. To improve waterproof-breathable characteristics of the membrane, the effects of electrospinning parameters on the fibers morphology and waterproof-breathable characteristics were investigated. PU concentration of 12% (w/w) and electrospinning voltage of 12 kV were identified as optimal conditions to reach uniform and fine PU nanofibers formation without any beads. Air permeability, water vapor transport rate, and resistance to water penetration average value for the final sample were recorded as about 2.5 ml/s, 840 g/m 2

A novel functional multilayer coating with periodically stacked nanolayers of amorphous carbon (a:C)/tungsten carbide (WC) and an adhesion layer of chromium (Cr) was deposited on 304 stainless steel using a dual magnetron sputtering technique. Through process optimization, highly densified coatings with high elasticity and shear modulus, excellent wear resistance, and minimal susceptibility to corrosive and caustic media could be acquired. The structural and mechanical properties of the optimized coatings were studied in detail using a variety of analytical techniques. Furthermore, finite element method simulations indicated that the stress generated due to contact against a steel ball was distributed well within the coating, which allowed the stresses to be lower than the yield threshold of the coating. Thus, an ultralow wear rate of ∼10mm/N mm could be achieved in dry sliding conditions under relatively high Hertzian contact pressures of ∼0.4-0.9 GPa. The amorphous and pinhole-free structure of the individual layers, sufficient number of pairs, and the relatively dense stacked layers resulted in significant polarization resistance (Z″ = 5.5 × 10 Ω cm) and increased the corrosion resistance of the coating by 10-fold compared to that of recently reported corrosion-resistant coatings.

No abstract

This work summarizes the design and construction of the first Iranian 115 kJ Mather type plasma focus (PF) machine (IR-MPF-100). This machine consists of a 6.25 cm radius and 22 cm height brass made anode with a 50 mm height insulator which separates the anode and cathode electrodes. Twelve copper made 22 cm height rods play the role of cathode with 10.2 cm radius. Twenty four 6 lF capacitors were used with the maximum charging voltage of 40 kV (maximum energy of 115 kJ) as the capacitor bank and maximum theoretical current around 1.224 MA. The total inductance of the system is 120 nH. By using NE-102 plastic Scintillator, Rogowski coil, current and voltage probes, hard X-ray, current derivative, current and voltage signals of IR-MPF-100 were measured. The primary result of neutron detection by neutron activation counter represents approximately 10 9 neutrons per shot at 65 kJ discharge energy while using deuterium filling gas. Also IR-MPF-100 PF has been tested successfully at 90 kJ by using the argon gas.

This paper reports the simulation of an electron gun. The effects of some parameters on the beam quality were studied and optimal choices were identified. It gives numerical beam qualities in common electrostatic triode gun, and the dependences on design parameters such as electrode geometries and bias voltages to these electrodes are shown. An electron beam of diameter 5 mm with energy of 5 keV was assumed for simulation process. Some design parameters were identified as variable parameters in the presence of space charge. These parameters are the inclination angle of emission electrode, the applied voltage to focusing electrode, the gap width between the emission electrode and the focusing electrode and the diameter of the focusing electrode. The triode extraction system is designed and optimized by using CST software (for Particle Beam Simulations). The physical design of the extraction system is given in this paper. From the simulation results, it is concluded that the inclination angle of the emission electrode is optimized at 22.5•, the applied voltage to the focusing electrode was optimized and found at Vfoc = -600 V, also, the separation distance (gap between emission electrode and focusing electrode) = 4 mm, and the diameter of the emission electrode = 14 mm.K ey wor ds: electron gun, electron beam trajectories, beam emittance and beam diameter, focusing voltage.