The oregano leaves’ extract (ORLE) was used for the formation of silver nanoparticles (AgNPs(ORLE)). ORLE and AgNPs(ORLE) (2 mg/mL) were dispersed in polymer hydrogels to give the pHEMA@ORLE_2 and pHEMA@AgNPs(ORLE)_2 using hydroxyethyl–methacrylate (HEMA). The materials were characterized by X-ray fluorescence (XRF) spectroscopy, X-ray powder diffraction analysis (XRPD), thermogravimetric differential thermal analysis (TG-DTA), derivative thermogravimetry/differential scanning calorimetry (DTG/DSC), ultraviolet (UV-Vis), and attenuated total reflection mode (ATR-FTIR) spectroscopies in solid state and UV–Vis in solution. The crystallite size value, analyzed with XRPD, was determined at 20 nm. The antimicrobial activity of the materials was investigated against Gram-negative bacterial strains Pseudomonas aeruginosa (P. aeruginosa) and Escherichia coli (E. coli). The Gram-positive ones of the genus of Staphylococcus epidermidis (S. epidermidis) and Staphylococcus aureus (S. aureus) are known to be involved in microbial keratitis by the means of inhibitory zone (IZ), minimum inhibitory concentration (MIC), and minimum bactericidal concentration (MBC). The IZs, which developed upon incubation of P. aeruginosa, E. coli, S. epidermidis, and S. aureus with paper discs soaked in 2 mg/mL of AgNPs(ORLE), were 11.7 ± 0.7, 13.5 ± 1.9, 12.7 ± 1.7, and 14.3 ± 1.7 mm. When the same dose of ORLE was administrated, the IZs were 10.2 ± 0.7, 9.2 ± 0.5, 9.0 ± 0.0, and 9.0 ± 0.0 mm. The percent of bacterial viability when they were incubated over the polymeric hydrogel discs of pHEMA@AgNPs(ORLE)_2 was interestingly low (66.5, 88.3, 77.7, and 59.6%, respectively, against of P. aeruginosa, E. coli, S. epidermidis, and S. aureus) and those of pHEMA@ORLE_2 were 89.3, 88.1, 92.8, and 84.6%, respectively. Consequently, pHEMA@AgNPs(ORLE)_2 could be an efficient candidate toward the development of non-infectious contact lenses.

The photosensitivity to 248nm excimer laser radiation of Er-doped Schott IOG-1 phosphate glass is presented. The photosensitive mechanism is investigated by employing a grating recording process. Index changes of up to ~2.0x10(-3) were measured in silver ion-exchanged samples using diffraction efficiency measurements; whereas changes of only ~10(-5) were measured for non-ion-exchanged samples. Absorption measurements allowed the identification of specific color center bands, which were attributed to the glass matrix and to the silver ions. Investigation of the exposed ion-exchanged glass using scanning electron microscopy and energy dispersive x-ray microanalysis revealed that in addition to the color centers formed, silver ion migration and ionization contribute significantly to the UV-induced index changes.

Diffractive optics fabrication is performed by two complementary processing methods that rely on the photoablation of materials by ultrashort UV laser pulses. The spatially selective ablation of materials permits the direct microetching of high-quality surface-relief patterns. In addition, the direct, spatially selective transfer of the ablated material onto planar and nonplanar receiving substrates provides a complementary microprinting operation. The radiation from the ultrashort pulsed excimer laser results in superior quality at relatively low-energy density levels, owing to the short absorption length and minimal thermal-diffusion effects. Computer-generated holographic structures are produced by both modes of operation. Submicrometer features, including Bragg-type structures, are microprinted onto planar and high-curvature optical-fiber surfaces, demonstrating the unique ability of the schemes for complex microstructure and potentially nanostructure development.