In recent years, a considerable interest has been drawn to microwave heating of powder metals and other electrically conductive materials. In this paper a consistent formulation describing the absorption of microwaves in electrically conductive materials under different microwave heating conditions is developed. A special case when conductive powder particles are surrounded by insulating oxide layers is investigated in detail using the effective-medium approximation. The conditions giving rise to skin effect governed, volumetric, and localized microwave heating are analyzed. Experimental observations of different microwave heating regimes in silicon, iron, and copper powder compacts are in general agreement with the theoretical model.
Temperature gradients that develop in ceramic materials during microwave heating are known to be strongly dependent on the applied microwave frequency. To gain a better understanding of this dependence, identical samples of ZnO powder compacts were microwave heated at three distinct widely separated frequencies of 2.45, 30, and 83 GHz and the core and surface temperatures were simultaneously monitored. At 2.45 GHz, the approximately uniform “volumetric” heating tends to raise the temperature of the sample as a whole, but the interior becomes hotter than the exterior because of heat loss from the surface. At 30 and 83 GHz, this interior to exterior temperature difference was found to be reversed, especially for high heating rates. This reversal resulted from increased energy deposition close to the sample's surface associated with reduced skin depth. A model for solving Maxwell's equations was incorporated into a newly developed two‐dimensional (2‐D) heat transport simulation code. The numerical simulations are in agreement with the experimental results. Simultaneous application of two or more widely separated frequencies is expected to allow electronic tailoring of the temperature profile during sintering.
The results of a study of ultra-rapid (flash) sintering of oxide ceramic materials under microwave heating with high absorbed power per unit volume of material (10–500 W/cm3) are presented. Ceramic samples of various compositions—Al2O3; Y2O3; MgAl2O4; and Yb(LaO)2O3—were sintered using a 24 GHz gyrotron system to a density above 0.98–0.99 of the theoretical value in 0.5–5 min without isothermal hold. An analysis of the experimental data (microwave power; heating and cooling rates) along with microstructure characterization provided an insight into the mechanism of flash sintering. Flash sintering occurs when the processing conditions—including the temperature of the sample; the properties of thermal insulation; and the intensity of microwave radiation—facilitate the development of thermal runaway due to an Arrhenius-type dependency of the material’s effective conductivity on temperature. The proper control over the thermal runaway effect is provided by fast regulation of the microwave power. The elevated concentration of defects and impurities in the boundary regions of the grains leads to localized preferential absorption of microwave radiation and results in grain boundary softening/pre-melting. The rapid densification of the granular medium with a reduced viscosity of the grain boundary phase occurs via rotation and sliding of the grains which accommodate their shape due to fast diffusion mass transport through the (quasi-)liquid phase. The same mechanism based on a thermal runaway under volumetric heating can be relevant for the effect of flash sintering of various oxide ceramics under a dc/ac voltage applied to the sample.
Yb:(LaY)2O3 ceramic samples have been sintered to almost full density in a fast microwave heating process with zero hold time. Rapid densification is observed at heating rates ranging from 50°C to 2400°C/min. The estimated value of the power absorbed in the materials per unit volume is from 10 to 400 W/cm3, which is similar to the processes of flash sintering under an applied dc/ac voltage. The microstructure of the sintered samples exhibits traces of a liquid‐like intergranular phase. The observed flash microwave sintering effect is associated with both preferential microwave absorption and enhanced mass transport within the softened grain boundaries arising due to an elevated concentration of defects and impurities therein. The volumetric nature of microwave heating gives rise to thermal stresses which can act as an additional driving force for sintering. The advantage of the microwave flash sintering process is that no electrodes are needed to supply the power to the articles undergoing sintering.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.