Electron emission from ferroelectrics ͑FEE͒ is an unconventional electron emission effect. Methods of FEE excitation are quite different compared to classic electron emission from solids. Two kinds of FEE have been observed, ''weak'' and ''strong.'' ''Weak'' electron emission ͑current density 10 Ϫ12-10 Ϫ7 A/cm 2 ͒ occurs from polar surfaces of ferroelectric materials in the ferroelectric phase only. A source of the electric field for ''weak'' FEE excitation is an uncompensated charge, generated by a deviation of macroscopic spontaneous polarization from its equilibrium state under a pyroelectric effect, piezoelectric effect, or polarization switching. The FEE is a tunneling emission current which screens uncompensated polarization charges. It is shown that the FEE is an effective tool for direct domain imaging and studies of electronic properties of ferroelectrics. ''Strong'' FEE, which is 10-12 orders of magnitude higher than ''weak'' FEE, achieves 100 A/cm 2 and is plasma-assisted electron emission. Two modes of the surface flashover plasma formation followed by strong electron emission have been studied. The plasma of ferroelectric origin has been observed only in the ferroelectric phase and it is induced by polarization switching or a field-enforced phase transition, such as antiferroelectric-ferroelectric or relaxor-ferroelectric. The second mode of plasma is conventional surface flashover which may be initiated by a high voltage application in any phase from any dielectric, including ferroelectrics. In this review paper we consider numerous experimental results, as well as mechanisms of both types of electron emission from ferroelectrics. The main stress is placed on the material aspect in order to clarify the influence of ferroelectricity ͑ferroelectric phase transitions, polarization switching, etc.͒ on electron emission. Another aspect which is broadly discussed is the potential applications of these unconventional FEE emitters in various devices for development of high density FEE cathodes for microwave devices, as well as FEE converters of IR irradiation into visible light, x-ray imaging, FEE flat panel displays, etc.

The discharge parameters in Hall thrusters depend strongly on the yield of secondary electron emission from channel walls. Comparative measurements of the yield of secondary electron emission at low energies of primary electrons were performed for several dielectric materials used in Hall thrusters with segmented electrodes. The measurements showed that at low energies of primary electrons the actual energetic dependencies of the total yield of secondary electron emission could differ from fits, which are usually used in theoretical models. The observed differences might be caused by electron backscattering, which is dominant at lower energies and depends strongly on surface properties. Fits based on power or linear laws are relevant at higher energies of primary electrons, where the bulk material properties play a decisive role.

We present results of the investigation of different types of cathodes operating in an electron diode powered by a high-voltage generator (300 kV, 250 ns, 84 Ω, ⩽5 Hz). The cathodes which have the same emitting area of 100 cm2 are made of metal–ceramic, carbon fibers, carbon fabric, velvet, or corduroy. We also tested carbon fibers and carbon fabric cathodes coated by CsI. It was shown that for all types of cathodes the electron emission occurs from the plasma which is formed as a result of a flashover of separate emitting centers. The amount of the emitting centers and the time delay in the electron emission were found to depend strongly on the accelerating electric field growth rate. Experimental data concerning the uniformity of the light emission from the cathode surface and divergence of the generated electron beams are presented. Data related to the general parameters of the diode, namely its impedance, power, and energy are given as well. For all the cathodes investigated the observed diode impedance indicated the existence of a quasistationary cathode plasma boundary for electron current density ⩽20 A/cm2. We present the dependencies of the average emitted electron current density and of the time delay in the electron emission on the number of generator shots. We also present data of the vacuum deterioration as a result of the tested cathodes operation. The obtained data are discussed within the framework of plasma formation as a result of cathode surface flashover.

Tri Alpha Energy's experimental program has demonstrated reliable field-reversed configuration (FRC) formation and sustainment, driven by fast ions via high-power neutral-beam (NB) injection. The world's largest compact-toroid device, C-2U, was upgraded from C-2 with the following key system upgrades: increased total NB input power from ~4 MW (20 keV hydrogen) to 10+ MW (15 keV hydrogen) with tilted injection angle; enhanced edge-biasing capability inside of each end divertor for boundary/stability control. C-2U experiments with those upgraded systems have successfully demonstrated dramatic improvements in FRC performance and achieved sustainment of advanced beam-driven FRCs with a macroscopically stable and hot plasma state for up to 5+ ms. Plasma diamagnetism in the best discharges has reached record lifetimes of over 11 ms, timescales twice as long as C-2. The C-2U plasma performance, including the sustainment feature, has a strong correlation with NB pulse duration, with the diamagnetism persisting even several milliseconds after NB termination due to the accumulated fast-ion population by NB injection. Power balance analysis shows substantial improvements in equilibrium and transport parameters, whereby electron energy confinement time strongly correlates with electron temperature; i.e. the confinement time in C-2U scales strongly with a positive power of T e .