Recent experiments at ASDEX Upgrade have achieved advanced scenarios with high β N (>3) and confinement enhancement over ITER98(y, 2) scaling, H H98y2 = 1.1-1.5, in steady state. These discharges have been obtained in a modified divertor configuration for ASDEX Upgrade, allowing operation at higher triangularity, and with a changed neutral beam injection (NBI) system, for a more tangential, off-axis beam deposition. The figure of merit, β N H ITER89-P , reaches up to 7.5 for several seconds in plasmas approaching stationary conditions. These advanced tokamak discharges have low magnetic shear in the centre, with q on-axis near 1, and edge safety factor, q 95 in the range 3.3-4.5. This q-profile is sustained by the bootstrap current, NBI-driven current and fishbone activity in the core. The off-axis heating leads to a strong peaking of the density profile and impurity accumulation in the core. This can be avoided by adding some central heating from ion cyclotron resonance heating or electron cyclotron resonance heating, since the temperature profiles are stiff in this advanced scenario (no internal transport barrier). Using a combination of NBI and gas fuelling line, average densities up to 80-90% of the Greenwald density are achieved, maintaining good confinement. The best integrated results in terms of confinement, stability and ability to operate at high density are obtained in highly shaped configurations, near double null, with δ = 0.43. At the highest densities, a strong reduction of the edge localized mode activity similar to type II activity is observed, providing a steady power load on the divertor, in the range of 6 MW m −2 , despite the high input power used (>10 MW).

ASDEX Upgrade has recently finished its transition towards an all-W divertor tokamak, by the exchange of the last remaining graphite tiles to W-coated ones. The plasma start-up was performed without prior boronization. It was found that the large He content in the plasma, resulting from DC glow discharges for conditioning, leads to a confinement reduction. After the change to D glow for inter-shot conditioning, the He content quickly dropped and, in parallel, the usual H-Mode confinement with H factors close to one was achieved. After the initial conditioning phase, oxygen concentrations similar to that in previous campaigns with boronizations could be achieved. Despite the removal of all macroscopic carbon sources, no strong change in C influxes and C content could be observed so far. The W concentrations are similar to the ones measured previously in discharges with old boronization and only partial coverage of the surfaces with W. Concomitantly it is found that although the W erosion flux in the divertor is larger than the W sources in the main chamber in most of the scenarios, it plays only a minor role for the W content in the main plasma. For large antenna distances and strong gas puffing, ICRH power coupling could be optimized to reduce the W influxes. This allowed a similar increase of stored energy as yielded with comparable beam power. However, a strong increase of radiated power and a loss of H-Mode was observed for conditions with high temperature edge plasma close to the antennas. The use of ECRH allowed keeping the central peaking of the W concentration low and even phases of improved H-modes have already been achieved.

The spatial distribution of density in a fusion experiment is of significant importance as it enters in numerous analyses and contributes to the fusion performance. The reconstruction of the density profile is therefore commonly done in offline data analysis. In this article, we present an algorithm which allows for density profile reconstruction from the data of the submillimeter interferometer and the magnetic equilibrium in real-time. We compare the obtained results to the profiles yielded by a numerically more complex offline algorithm. Furthermore, we present recent ASDEX Upgrade experiments in which we used the real-time density profile for active feedback control of the shape of the density profile.

The ASDEX Upgrade (AUG) programme is directed towards physics input to critical elements of the ITER design and the preparation of ITER operation, as well as addressing physics issues for a future DEMO design. Since 2015, AUG is equipped with a new pair of 3-strap ICRF antennas, which were designed for a reduction of tungsten release during ICRF operation. As predicted, a factor two reduction on the ICRF-induced W plasma content could be achieved by the reduction of the sheath voltage at the antenna limiters via the compensation of the image currents of the central and side straps in the antenna frame. There are two main operational scenario lines in AUG. Experiments with low collisionality, which comprise current drive, ELM mitigation/suppression and fast ion physics, are mainly done with freshly boronized walls to reduce the tungsten influx at these high edge temperature conditions. Full ELM suppression and non-inductive operation up to a plasma current of I p = 0.8 MA could be obtained at low plasma density. Plasma exhaust is studied under conditions of high neutral divertor pressure and separatrix electron density, where a fresh boronization is not required. Substantial progress could be achieved for the understanding of the confinement degradation by strong D puffing and the improvement with nitrogen or carbon seeding. Inward/outward shifts of the electron density profile relative to the temperature profile effect the edge stability via the pressure profile changes and lead to improved/decreased pedestal performance. Seeding and D gas puffing are found to effect the core fueling via changes in a region of high density on the high field side (HFSHD). The integration of all above mentioned operational scenarios will be feasible and naturally obtained in a large device where the edge is more opaque for neutrals and higher plasma temperatures provide a lower collisionality. The combination of exhaust control with pellet fueling has been successfully demonstrated. High divertor enrichment values of nitrogen E N ⩾ 10 have been obtained during pellet injection, which is a prerequisite for the simultaneous achievement of good core plasma purity and high divertor radiation levels. Impurity accumulation observed in the all-metal AUG device caused by the strong neoclassical inward transport of tungsten in the pedestal is expected to be relieved by the higher neoclassical temperature screening in larger devices.