A high pressure oil or gas well can be used to enhance both the production and the total recovery from a depleted well using a multiphase ejector. This device does not require any power supply and is characterized by a simple design, absence of moving parts and small dimensions, coupled with a high degree of reliability and low cost. The main disadvantages related with the use of multiphase ejectors are due to the lack of reliable design methods and to the sharp decrease of the performance when operative conditions change. In August 2002 a multiphase ejector has been installed in Allegheny TLP, GOM, to boost the production from a depleted well. In the present paper the design method and the results of field tests of the Allegheny ejector are presented. From a practical view-point the main result of this installation has been an increase of production of 1300 BOPD with an investiment of less than 50,000 USD. Introduction The ejector or Jet Pump, JP, is an artificial lift method which does not require any power supply and is characterized by a simple structural design, absence of moving parts and small dimensions, which allows easy installation and management procedures during fields operations, coupled with a high degree of reliability and low cost of installation, compared with other boosting systems. On the other hand, the ejector is a low-efficiency device: just a small fraction of the power fluid energy (approximately 20-30%) is actually transferred to the low pressure fluid (however it should be remarked that in many cases this energy would be lost through a choke valve). When the ejector is fed with multiphase fluids, significant modelling problems arise and no established methods are available for the design of multiphase ejectors. Design problems are increased by fluid properties changes during field evolution. To cope with all these problems and extend the operative life of the ejector, an advanced multiphase ejector has been developed in order to optimise some of the main geometrical parameters and improve the ejector performances at varying operative conditions. In this paper, the realization and field application of this multiphase ejector are described. Fig. 1 shows the main components of a JP: the nozzle, the mixing chamber followed by the mixing duct and the diffuser sections. Power fluid, at an injection pressure Pd is forced through the nozzle. As the fluid accelerates because of the area reduction, its kinetic energy increases and the pressure decreases to the value Pn at the nozzle exit section. The power and the produced fluids then enter the mixing chamber were pressure reaches its minimum value, Ps. In the mixing chamber, mixing duct and diffuser the pressure increases and the gas-liquid mixture leaves the ejector at a pressure Pl. The main concern about actual multiphase ejectors is the limited capability of the hardware to be adjusted when boundary conditions change (i.e. well depletion, water cut and/or GOR variation, production profiles). To this aim, the present multiphase ejector has been designed to be adaptable in terms of:
ENI E&P in 1993 launched an R&D project on production boosting using multiphase jet pumps. In these devices a high pressure oil or gas well can be used to enhance both the production and the total recovery from a depleted well. The multiphase ejector is characterized by a simple design, absence of moving parts and small dimensions, coupled with a high degree of reliability and low cost. The main disadvantages related to the use of multiphase ejectors are due to the lack of reliable design methods and to the sharp decrease of the performance when operative conditions change. In the last three years the ejector technology can be considered a standard for ENI resulted in several successful installations worldwide:West Africa (onshore oil wells)GOM (offshore, condensate gas)Italy and Mediterranean Sea (onshore and offshore, wet and dry gases) In the present work a status of these installations is reported, pointing out the following main items:design and installation peculiaritiespredicted and measured performancesoptimisation actions performed during the considered period The results of this review have been used to identify the new strategies on ejector design and operability, which will be also reported. In particular, new design to increase productivity and component operability life is described, together with laboratory test results. Introduction The multiphase ejector or Jet Pump, MJP, is an artificial lift method characterized by a simple structural design, absence of moving parts and small dimensions, which allows easy installation and management procedures during field operations, coupled with a high degree of reliability and low cost of installation, compared to other boosting systems. On the other hand, the ejector is a low-efficiency device: just a small fraction of the power fluid energy (approximately 20–30%) is actually transferred to the low pressure fluid. When the ejector is fed with multiphase fluids, significant modeling problems arise and no established methods are available for the design of multiphase ejectors. Design problems are increased by fluid property changes during field evolution. To cope with all these problems and extend the operative life of the ejector, an advanced multiphase ejector has been developed in order to optimize some of the main geometrical parameters and to improve the ejector performances at varying operative conditions. In this paper, the realization and the field application of this multiphase ejector are described. Multiphase Ejector Characteristics Fig. 1 shows the main components of a JP: the nozzle, the mixing chamber followed by the mixing duct and the diffuser sections. Power fluid, at an injection pressure Pd is forced through the nozzle. As the fluid accelerates because of the area reduction, its kinetic energy increases and the pressure decreases to the value Pn at the nozzle exit section. The power fluid and the produced fluids then enter the mixing chamber were the pressure reaches its minimum value, Ps. Inside the mixing chamber, mixing duct and diffuser the pressure increases and the gas-liquid mixture leaves the ejector at a pressure Pl. The main concern about actual multiphase ejectors is the limited capability of the hardware which have to be adjusted when boundary conditions change (i.e. well depletion, water cut and/or GOR variation, production profiles). To this aim, the present multiphase ejector has been designed to be adaptable in terms of:nozzle diametermixing chamber lengthmixing tube length and diameter, with the objective of improving as much as possible the performance of a conventional ejector.
The application of a new Multi Phase Flow Meter (MPFM) for monitoring the production of three gas wells in the Gulf of Mexico, Allegheny TLP, is presented. The meter is based on a sampling method, does not make use of γ-sources and is selfcalibrating. In the present application, it has been possible to compare the measurement of the MPFM with production data obtained from a conventional well testing system certified for production allocation. The accuracy of present measurements of the gas and total liquid flow rates is similar (or better) than the accuracy of the well testing system (± 2% of the actual readings). A special feature of this MPFM is the direct measurement of the condensate and water phase densities. This allows a very accurate measurement of the Water Volume Fraction, with an absolute uncertainty of WVF measurements equal to 0.001%. This value is two orders of magnitude better that the accuracy of other MPFMs under development. The measurement of the water phase density also permits an estimate of the methanol flow rate injected in the subsea pipeline to prevent hydrate formation.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.