Статья посвящена расчетному и экспериментальному определению частот и форм собственных колебаний сварного корпуса кориолисового расходомера. Кориолисов расходомер предназначен для измерения массово-го расхода жидкостей и газов. Корпус расходомера сварен из тонкостенных стальных пластин 12Х18Н10Т. Формы и частоты собственных колебаний корпуса определены расчетом с помощью метода конечных элементов и экспериментально с использованием технологии экспериментального мо-дального анализа. При экспериментальном определении модальных харак-теристик свободно вывешенного корпуса колебания возбуждали с исполь-зованием ударного молотка и модального вибростенда.Для оценки близости расчетных и экспериментальных форм использо-ван критерий модальной достоверности (Modal Assurance Criterion) MAC. Показано, что отличие частот и форм собственных колебаний корпуса меж-ду расчетом и экспериментом превышает 30 %, а отличие между частотами и формами собственных колебаний отдельных элементов корпуса, не со-держащих сварных соединений, не превышает 3 %. Тогда наиболее вероят-ной причиной расхождения расчетных и экспериментальных частот и форм собственных колебаний корпуса являются сварные соединения, не учиты-ваемые в его конечноэлементной модели.Выдвинуто предположение о том, что столь существенное различие можно объяснить возникающими после сварки остаточными напряжения-ми. Для проверки этой гипотезы выполнен отпуск сваренного корпуса. Ус-тановлено, что после отпуска отличие между расчетными и эксперимен-тальными формами и частотами собственных колебаний корпуса снизилось до 6 %. Полученный результат позволил объяснить причину расхождения расчетных и экспериментальных частот и форм собственных колебаний корпуса расходомера.Ключевые слова: кориолисов расходомер; метод конечных элементов; соб-ственная частота; собственная форма; экспериментальный модальный анализ; критерий модальной достоверности МАС; остаточные напряжения.
ВведениеКориолисов расходомер предназначен для измерения массового расхода жидкостей и газов. Он состоит из корпуса и двух расположенных в нем U-образных колеблющихся трубок, по кото-рым движется измеряемая среда. Обзор конструкций кориолисовых расходомеров приведен в [1, 2], а подробное описание принципа их работы в [3].При исследовании динамических характеристик расходомера в статье [4] установлено, что формы и частоты собственных колебаний трубок, полученные методом конечных элементов и экспериментально, практически совпадают. Формы колебаний корпуса в статье [4] не рассматри-вались. Дальнейшие исследования показали, что в отличие от трубок частоты и формы собствен-ных колебаний корпуса, полученные расчетом и экспериментально, различаются более чем на 30 %. Поиску причин расхождения между расчетными и экспериментальными частотами и фор-мами собственных колебаний сварного корпуса кориолисового расходомера и посвящена данная статья.