Zirconia/alumina functionally graded material made by ceramic ink jet printing

Mott, Matthew; Evans, Jrg

doi:10.1016/s0921-5093(99)00266-x

Cited by 122 publications

(76 citation statements)

References 21 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…The DIP technique has also been applied to create parts from wax-based alumina inks, [24][25][26] demonstrating the suitability of low-melting point waxes for hot-melt ink-jet printing. A functionally graded composite was printed from zirconia and alumina inks by Mott and Evans, [23] whereas the one-dimensional gradient was comparable to the predicted composition. Alcohol-based zirconia inks were also applied to manufacture complex-shaped geometries, which may be used as miniature heat exchangers.…”

Section: Three-dimensional Printing (3dp)mentioning

confidence: 97%

“…[20][21][22] In addition, DIP allows microstructure tailoring through blending and diluting the ceramic suspensions, leading to a graded composition of the printed body. [23] The ceramic inks are typically prepared according to two methods: using wax-based inks, which are deposited in hotmelted state and solidify on a cold substrate, [24][25][26] or using ceramic suspensions, which dry through evaporation of the liquid. [27,28] Reis et al [29] claimed that loaded wax containing up to 45 vol% of particles can be successfully ink-jet printed, whereas the maximum solid content reported for an aqueous suspension amounted27 vol%.…”

Section: Three-dimensional Printing (3dp)mentioning

confidence: 99%

See 1 more Smart Citation

Additive Manufacturing of Ceramic‐Based Materials

et al. 2014

View full text Add to dashboard Cite

This paper offers a review of present achievements in the field of processing of ceramic-based materials with complex geometry using the main additive manufacturing (AM) technologies. In AM, the geometrical design of a desired ceramic-based component is combined with the materials design. In this way, the fabrication times and the product costs of ceramic-based parts with required properties can be substantially reduced. However, dimensional accuracy and surface finish still remain crucial features in today's AM due to the layer-by-layer formation of the parts. In spite of the fact that significant progress has been made in the development of feedstock materials, the most difficult limitations for AM technologies are the restrictions set by material selection for each AM method and aspects considering the inner architectural design of the manufactured parts. Hence, any future progress in the field of AM should be based on the improvement of the existing technologies or, alternatively, the development of new approaches with an emphasis on parts allowing the near-net formation of ceramic structures, while optimizing the design of new materials and of the part architecture.

show abstract

Section: Three-dimensional Printing (3dp)mentioning

confidence: 97%

Section: Three-dimensional Printing (3dp)mentioning

confidence: 99%

Additive Manufacturing of Ceramic‐Based Materials

et al. 2014

View full text Add to dashboard Cite

show abstract

“…For DCIJP a number of different inks has already been investigated. Ceramic powders used for the inks include ZrO 2 [7][8][9][10], Al 2 O 3 [11,9,10], TiO 2 [12], BaTiO 3 [13] or PZT [14,15]. Also different technologies were applied for fabrication of parts, including continuous [13] and drop-on-demand printing [7,8,4,16,17].…”

Section: Introductionmentioning

confidence: 99%

“…Discussed solvent systems include water [15,7,19,13], octane, hexene or isopropyl alcohol [17], ethyl alcohol [11,9,10] or water/glycerol mixtures [12]. Reverse microemulsions are also reported to be adequate solvents systems [20].…”

Section: Introductionmentioning

confidence: 99%

Highly loaded alumina inks for use in a piezoelectric print head

Polsakiewicz¹,

Kollenberg

2011

Materialwissenschaft Werkst

View full text Add to dashboard Cite

Ink jet printing techniques are used for an increasing number of materials and applications. Properties of the used inks have great influence on process stability and accuracy as well as the resulting part properties. Inks containing ceramic particles have been applied in various studies and applications. The criteria identifying suitable inks vary depending on the applied printing technology. In this study, inks for application in a piezoelectric print head were investigated. Alumina inks with solid loadings up to 21 vol.-% were prepared and characterized. The Influence of different solid loadings, dispersant concentrations and binding agents was examined. The prepared inks show sufficient stability and fit literature recommendations for successful drop ejection. Considering rheological aspects, two inks with light shear-thinning behaviour and viscosities of 18 mPas and 23 mPas at high shear rates were recommended for upcoming printing tests. The Re/We 1/2 ratio can be used for predetermination of print ability but the influence of the surface tension is not sufficiently taken into account using the presented calculations. So further printing experiments are essential for clarification of the calculations and obtained print ability values. Keywords: Suspension / particle processing / materials processing / rheology / alumina /

show abstract

“…Posle sagorevanja organske komponente debljina sloja je jednaka prosečnom dijametru sinterovanog zrna, a zavisi od prirode keramike i temperature sinterovanja. Kompjuterskim programom se kontrolišu oblik i debljina slojeva, kao i mikrostruktura [31].…”

Section: (D) Elektroforetska Depozicija (Efd)unclassified

Synthesis and characterization of BaTi1-xSnxO3 powders and multilayered ceramic materials

Marković¹

View full text Add to dashboard Cite

Zirconia/alumina functionally graded material made by ceramic ink jet printing

Cited by 122 publications

References 21 publications

Additive Manufacturing of Ceramic‐Based Materials

Additive Manufacturing of Ceramic‐Based Materials

Highly loaded alumina inks for use in a piezoelectric print head

Synthesis and characterization of BaTi1-xSnxO3 powders and multilayered ceramic materials

Contact Info

Product

Resources

About