Tuning DOS measuring parameters based on double-loop EPR in H2SO4 containing KSCN by Taguchi method

Momeni, Mojtaba; Moayed, Mohammad Hadi; Davoodi, Ali

doi:10.1016/j.corsci.2010.04.015

Cited by 41 publications

(12 citation statements)

References 16 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The DL-EPR method has been widely used to quantitatively examine DOS and IGC susceptibility in stainless steels. [30][31][32][33] Overall, the study shows that using TRDs as an effective and useful microstructural GB network descriptor provide enhanced insight into individual GB and GB network IGC phenomena in GBE stainless steel.…”

Section: Introductionmentioning

confidence: 77%

Tracking the evolution of intergranular corrosion through twin-related domains in grain boundary networks

et al. 2018

View full text Add to dashboard Cite

Tailoring the grain boundary network is desired to improve grain boundary-dependent phenomena such as intergranular corrosion. An important grain boundary network descriptor in heavily twinned microstructures is the twin-related domain, a cluster of twinrelated grains. We indicate the advantages of using twin-related domains and subsequent statistics to provide new insight into how a grain boundary networks respond to intergranular corrosion in a heavily twinned grain boundary engineered 316L stainless steel. The results highlight that intergranular corrosion is typically arrested inside twin-related domains at coherent twins or low-angle grain boundaries. Isolated scenarios exist, however, where intergranular corrosion propagation persists in the grain boundary network through higher-order twin-related boundaries.

show abstract

Section: Introductionmentioning

confidence: 77%

Tracking the evolution of intergranular corrosion through twin-related domains in grain boundary networks

et al. 2018

View full text Add to dashboard Cite

show abstract

“…Double loop electrochemical potentiokinetic reactivation (DLEPR) technique was used for sensitization studies through DOS evaluation of the specimens comprising of weld metal as well as HAZs representing different weldments (as-welded as well as thermally aged) as suggested by the previously reported studies [19][20][21][22]. The specimen sampling plan for degree of sensitization (DOS) studies as represented schematically through Fig.…”

Section: Dos Evaluation Of the Weld Metal And The Haz Of The Joints Umentioning

confidence: 99%

Studies on metallurgical and impact toughness behavior of variably sensitized weld metal and heat affected zone of AISI 304L welds

Kumar

Shahi

2016

Materials & Design

View full text Add to dashboard Cite

“…Pishbina et al (2010) investigated the effects of processing parameters, including suspension concentration, pH, and electric field by Taguchi's design of experiment (DOE) approach in electrophoretic deposition of bioglass suspension. Momeni et al (2010) obtained the optimal condition for the degree of sensitization (DOS) measurement based on double-loop EPR technique in H 2 SO 4 -containing KSCN solution by Taguchi method. In this paper, it is concluded that the higher S/N ratio, the greater is the effect on the DOS measurement.…”

Section: Introductionmentioning

confidence: 99%

Optimisation of shock absorber process parameters using failure mode and effect analysis and genetic algorithm

2013

View full text Add to dashboard Cite

The various process parameters affecting the quality characteristics of the shock absorber during the process were identified using the Ishikawa diagram and by failure mode and effect analysis. The identified process parameters are welding process parameters (squeeze, heat control, wheel speed, and air pressure), damper sealing process parameters (load, hydraulic pressure, air pressure, and fixture height), washing process parameters (total alkalinity, temperature, pH value of rinsing water, and timing), and painting process parameters (flowability, coating thickness, pointage, and temperature). In this paper, the process parameters, namely, painting and washing process parameters, are optimized by Taguchi method. Though the defects are reasonably minimized by Taguchi method, in order to achieve zero defects during the processes, genetic algorithm technique is applied on the optimized parameters obtained by Taguchi method.

show abstract

Tuning DOS measuring parameters based on double-loop EPR in H2SO4 containing KSCN by Taguchi method

Cited by 41 publications

References 16 publications

Tracking the evolution of intergranular corrosion through twin-related domains in grain boundary networks

Tracking the evolution of intergranular corrosion through twin-related domains in grain boundary networks

Studies on metallurgical and impact toughness behavior of variably sensitized weld metal and heat affected zone of AISI 304L welds

Optimisation of shock absorber process parameters using failure mode and effect analysis and genetic algorithm

Contact Info

Product

Resources

About