Transient piezothermoelastic analysis of a cross-ply laminated cylindrical panel bonded to a piezoelectric actuator

Ootao, Yoshihiro; Tanigawa, Yoshinobu

doi:10.1016/j.apm.2004.09.006

Cited by 3 publications

(1 citation statement)

References 13 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Wang and Ding were analyzed one-dimensional dynamic piezothermoelastic problems of a two-layered composite hollow cylinder constructed of elastic and piezoelectric layers [20]. We analyzed the transient piezothermoelastic problems for cylindrical composite panels when the piezoelectric layer is used as a sensor [21,22] or an actuator [23,24]. To the author's knowledge, however, the analytical studies for transient piezothermoelastic problem of laminated composite hollow cylinders due to asymmetrical heating have not been reported.…”

Section: Introductionmentioning

confidence: 92%

Transient Piezothermoelasticity of a Two-Layered Composite Hollow Cylinder Constructed of Isotropic Elastic and Piezoelectric Layers Due to Asymmetrical Heating

Tanigawa

Ootao

2007

Journal of Thermal Stresses

Self Cite

View full text Add to dashboard Cite

This article is concerned with the theoretical treatment of transient piezothermoelastic problem involving a two-layered hollow cylinder constructed of isotropic elastic and piezoelectric layers due to asymmetrical heat supply. The transient two-dimensional temperature is analyzed by the method of Laplace transformation. By using the exact solutions for piezoelectric hollow cylinder and isotropic hollow cylinder, the theoretical analysis of transient piezothermoelasticity is developed for a two-layered composite hollow cylinder under the state of plane strain. As an example, numerical calculations are carried out for an isotropic elastic hollow cylinder made of steel, bonded to a piezoelectric layer of cadmium selenide. Some numerical results for the temperature change, the stress and the electric potential distributions in a transient state are shown in figures. Furthermore, the influence of thickness of the piezoelectric layer or the isotropic elastic layer upon the temperature change, stresses and electric potential is investigated.

show abstract

Section: Introductionmentioning

confidence: 92%

Transient Piezothermoelasticity of a Two-Layered Composite Hollow Cylinder Constructed of Isotropic Elastic and Piezoelectric Layers Due to Asymmetrical Heating

Tanigawa

Ootao

2007

Journal of Thermal Stresses

Self Cite

View full text Add to dashboard Cite

show abstract

Transient piezothermoelastic problems of smart composite structures bonded to a piezoelectric layer

Ootao

Tanigawa

2006

Struct. Control Health Monit.

View full text Add to dashboard Cite

Active vibration control of an arbitrary thick smart cylindrical panel with optimally placed piezoelectric sensor/actuator pairs

Hasheminejad

Oveisi

2015

Int J Mech Mater Des

View full text Add to dashboard Cite

Active vibration suppression of a simply supported, arbitrarily thick, transversely isotropic circular cylindrical host panel, integrated with spatially distributed piezoelectric actuator and sensor layers, is investigated based on the linear three dimensional exact piezo-elasticity theory. To assist control system design, system identification is conducted by applying a frequency domain subspace approximation method based on N4SID algorithm using the first few structural modes of the system. The state space model is constructed from system identification and used for state estimation and development of control algorithm. The optimal electrode configuration for the collocated piezoelectric actuator-sensor pair is found by applying a genetic optimization procedure based on maximization of a quantifiable objective function considering the controllability, observability and spillover prevention of the identified system. A linear quadratic Gaussian (LQG) optimal controller is subsequently designed and simulated based on the identified model of optimally configured smart structure in order to actively control the system response in both frequency and time domains. The dynamic performance and effectiveness of the optimized vibration control system is demonstrated for two different types of external mechanical excitations (i.e., impulsive load and white noise disturbance). The accuracy of dynamic analysis is established with the aid of a commercial finite element package and the data available in the literature.

show abstract

Transient piezothermoelastic analysis of a cross-ply laminated cylindrical panel bonded to a piezoelectric actuator

Cited by 3 publications

References 13 publications

Transient Piezothermoelasticity of a Two-Layered Composite Hollow Cylinder Constructed of Isotropic Elastic and Piezoelectric Layers Due to Asymmetrical Heating

Transient Piezothermoelasticity of a Two-Layered Composite Hollow Cylinder Constructed of Isotropic Elastic and Piezoelectric Layers Due to Asymmetrical Heating

Transient piezothermoelastic problems of smart composite structures bonded to a piezoelectric layer

Active vibration control of an arbitrary thick smart cylindrical panel with optimally placed piezoelectric sensor/actuator pairs

Contact Info

Product

Resources

About