Thermal fatigue, thermal expansion and mechanical properties of pitch-based carbon fiber reinforced 7075 aluminum alloy.

Ikuno, Hajime; Towata, Shin‐ichi; Yamada, Sen-ichi; Awano, Yoji

doi:10.2464/jilm.44.379

Cited by 6 publications

(1 citation statement)

References 0 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The composite is called a hybrid composite. Aluminum alloy matrix hybrid composites have been fabricated using the following reinforcements: continuous SiC fibers having SiC particles attached to their surfaces, 13) continuous carbon fibers having SiC particles and whiskers attached to their surfaces, 14,15) and continuous Tyranno fibers having -SiC particles attached to their surfaces. 16) As Al 2 O 3 (alumina) has high rigidity and strength, and outstanding resistance to heat and wear, the alumina can improve the strength of aluminum alloy not only at room temperature but also at high temperature.…”

Section: Introductionmentioning

confidence: 99%

Effects of Particle-Dispersion on the Strength of an Alumina Fiber-Reinforced Aluminum Alloy Matrix Composite

Asano

Yoneda

2003

Mater. Trans.

View full text Add to dashboard Cite

Aluminum alloy matrix hybrid composites, in which alumina particles were dispersed among continuous alumina fibers, were fabricated by squeeze casting, and the influence of temperature and the effects of the particle-dispersion on the strength of the composites were then investigated. The particle-dispersion among the fibers minimized preform contraction and fiber-to-fiber contact due to the melt infiltration during the squeeze casting. The tensile strength, 0.2% proof stress and elastic modulus of the composites in the longitudinal direction increased with increasing the fiber volume fraction, retaining nearly the same values up to 623 K. These values of the hybrid composite were larger than those of the particle-free composite at every temperature. This is because the fibers were distributed uniformly owing to the particles that prevented the fiber-to-fiber contact, leading to the reduction of stress concentration at the points of direct fiber contact, and stress transmission between the fiber and the matrix becomes easy. At every temperature, the transverse tensile strength and proof stress of the particle-free composite was lower than that of the unreinforced alloy, because the fracture was initiated at the fiber-to-fiber contact point and the cracks propagated mainly along the fiber-matrix interface. In contrast, the strength of the hybrid composite was close to that of the unreinforced alloy even at high-temperature, because the cracks propagated mainly throughout the matrix owing to the uniform distribution of the fibers and the strong fiber-matrix bond.

show abstract

Section: Introductionmentioning

confidence: 99%

Effects of Particle-Dispersion on the Strength of an Alumina Fiber-Reinforced Aluminum Alloy Matrix Composite

Asano

Yoneda

2003

Mater. Trans.

View full text Add to dashboard Cite

show abstract

Microstructure and mechanical properties of Al-Cu-Mg alloy matrix hybrid composites fabricated by squeeze casting

Asano¹,

Yoneda²

2002

International Journal of Cast Metals Research

View full text Add to dashboard Cite

Thermal expansion behaviour of squeeze-cast aluminium matrix composites reinforced with PAN- and Pitch-based carbon fibres

Asano

2017

International Journal of Cast Metals Research

View full text Add to dashboard Cite

Thermal fatigue, thermal expansion and mechanical properties of pitch-based carbon fiber reinforced 7075 aluminum alloy.

Cited by 6 publications

References 0 publications

Effects of Particle-Dispersion on the Strength of an Alumina Fiber-Reinforced Aluminum Alloy Matrix Composite

Effects of Particle-Dispersion on the Strength of an Alumina Fiber-Reinforced Aluminum Alloy Matrix Composite

Microstructure and mechanical properties of Al-Cu-Mg alloy matrix hybrid composites fabricated by squeeze casting

Thermal expansion behaviour of squeeze-cast aluminium matrix composites reinforced with PAN- and Pitch-based carbon fibres

Contact Info

Product

Resources

About