Theoretical Investigation of Advanced Capillary Structures in Grooved Heat Pipe Evaporators for Space Applications

Brandt, Christoph; Stephan, Peter; Dubois, M.; Mullender, Bernard

doi:10.4271/2000-01-2319

Cited by 7 publications

(7 citation statements)

References 6 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…As shown by the experimental research [9,10], the temperature drop in the steam passage channel depends on the amount of heat-transfer fluid filling the pipe, and on the tilt angle of the axis of the heat pipe to the horizon. The three operation modes of the smoothwall heat pipe (Fig.2) differ in the amount of filling heat-transfer fluid.…”

Section: Methodsmentioning

confidence: 99%

Experimental research of heat recuperators in ventilation systems on the basis of heat pipes

2017

View full text Add to dashboard Cite

Abstract. The paper presents the results of experimental studies of heat pipes and their thermo-technical characteristics (heat power, conductivity, heat transfer resistance, heat-transfer coefficient, temperature level and differential, etc.). The theoretical foundations and the experimental methods of the research of ammonia heat pipes made of aluminum section АS -КRА 7.5 -R1 (made of the alloy AD -31) are explained. The paper includes the analysis of the thermo-technical characteristics of heat pipes as promising highly efficient heat transfer devices, which may be used as the basic elements of heat exchangers -heat recuperators for exhaust ventilation air, capable of providing energy-saving technologies in ventilation systems for housing and public utilities and for various branches of industry. The thermo-technical characteristics of heat pipes (HP) as the basic elements of a decentralized supply-extract ventilation system (DSEVS) and energy-saving technologies are analyzed. As shown in the test report of the ammonia horizontal HP made of the section АS-КRА 7,5-R1-120, this pipe ensures safe operation under various loads.

show abstract

Section: Methodsmentioning

confidence: 99%

Experimental research of heat recuperators in ventilation systems on the basis of heat pipes

2017

View full text Add to dashboard Cite

show abstract

“…This causes the liquid fill amount inside the liquid channel to be so critical that a small decrease in liquid fill may result in a significant decrease in the capillary pumping pressure and, hence, a significant decrease in the maximum heat transport. Previous researchers, for example, Harwell et al, 1 Alario et al, 4 Henson, 6 and Brandt et al, 9 have modeled the flow of liquid in both reentrant groove heat pipes and in monogroove heat pipes as a one-dimensional laminar flow through a smooth-walled tube to determine the pressure drop (Po = f Re = 16). In addition, the effect of the shear stress at the liquid-vapor interface has not been accounted for.…”

Section: Introductionmentioning

confidence: 99%

Fluid Flow in Axial Reentrant Grooves with Application to Heat Pipes

Thomas

Damle

2005

Journal of Thermophysics and Heat Transfer

View full text Add to dashboard Cite

The fully developed laminar flow within a reentrant groove has been analyzed using a finite element model. A parametric analysis was carried out to determine the Poiseuille number Po = fRe, the dimensionless mean velocity v * , and the dimensionless volumetric flow rateV * as functions of the geometry of the reentrant groove (groove height 1.0 < -H * < -4.0, slot half-width 0.05 < -W * /2 < -0.9, and fillet radius 0.0 < -R * f < -1.0), and the liquid-vapor shear stress (0.0 < -− −τ * lv < -2.5). The case in which the meniscus recedes into the reentrant groove was examined and could be a result of evaporator dryout or insufficient liquid fill amount. The cross-sectional area of the liquid in the groove, A * l , the meniscus radius R * m , and the aforementioned flow variables were calculated as functions of the meniscus contact angle (0 < -φ < -40 deg) and the meniscus attachment point (0.0 < -H * l < -2.75). Finally, the results of the numerical model were used to determine the capillary limit of a low-temperature heat pipe with two different working fluids, water and ethanol, for a range of meniscus contact angles. Nomenclaturecenter of circular portion of reentrant groove to top of slot, m H l = vertical location of attachment point of meniscus to reentrant groove wall, m H l,s = vertical location of attachment point of meniscus to sinusoidal groove wall, m H s = height of sinusoidal groove, m H tr = height of trapezoidal groove, m H * = H/R H * l = H l /R h f g = heat of vaporization, J/kg K = thermal conductivity, W/(m · K) L a = adiabatic length, m L c = condenser length, m L e = evaporator length, m L eff = effective heat pipe length, L e /2 + L a + L c /2, m N g = number of grooves n = coordinate normal to the liquid-vapor interface n * = n/R P = wetted perimeter, m Po = Poiseuille number, f Re P * = P/R = pressure, N/m 2 Q cap = capillary limit heat transport, Ẇ Q g = heat transfer due to a single groove, Ẇ Q t = total heat transported, N gQ g , W q lv = heat flux at the liquid-vapor interface, W/m 2 q * lv = q lv /q R q = internal volumetric heat generation, W/m 3 R = radius of circular portion of reentrant groove, m Re = Reynolds number, ρv D h /µ R f = radius of fillet, m R m = radius of meniscus, m R v = radius of heat pipe vapor space, m R * fwidth of slot, m W l = width of liquid meniscus at attachment point to reentrant groove wall, m W l,s = width of liquid meniscus at attachment point to sinusoidal groove wall, m W s = width of sinusoidal groove, m W tr = width of trapezoidal groove, m W * = W/R W * l = W l /R x, y, z = Cartesian coordinate directions x f,0 , z f,0 = location of center point of circular fillet, m x t , z t = point of tangency of fillet and circular portion of reentrant groove, m x * , y * , z * = x/R, y/R, z/R x * f,0circular segment duct half-angle, rad 395 Downloaded by MONASH UNIVERSITY on February 3, 2015 | http://arc.aiaa.org | 396 THOMAS AND DAMLEβ = aspect ratio for rectangular and trapezoidal grooves, 2H r /W r or 2H tr /W tr γ = triangular groove half-angle, rad θ = trap...

show abstract

“…The dimensions of the grooves analyzed by Brandt et al [9] were used to determine the mean velocity, volumetric flow rate and Poiseuille number of liquid flowing in a re-entrant groove as a function of the amount of liquid in the groove. Faghri [18] gives values of the minimum meniscus contact angle for a receding meniscus for various liquids in contact with metal walls.…”

Section: B Effect Of Groove Fill Amountmentioning

confidence: 99%

“…Previous researchers (e.g., Harwell et al [1], Alario et al [4], Henson [6], Brandt et al [9]) have modelled the flow of liquid in both re-entrant groove heat pipes and in monogroove heat pipes as a one-dimensional laminar flow through a smooth-walled tube in order to determine the pressure drop (Po = f Re = 16). In addition, the effect of the shear stress at the liquid-vapor interface has not been accounted for.…”

mentioning

confidence: 99%

“…In addition, the effect of the shear stress at the liquid-vapor interface has not been accounted for. While Brandt et al [9] examined the effect of the liquid fill amount in the groove on the capillary pressure, only the case in which the liquid meniscus remained attached to the top of the slot was examined. The present study has addressed these shortcomings by numerically solving the conservation of mass and momentum equations for laminar fully-developed flow in re-entrant grooves with an applied shear stress at the liquid-vapor interface.…”

mentioning

confidence: 99%

See 1 more Smart Citation

Analysis of Fluid Flow in Axial Re-entrant Grooves with Application to Heat Pipes

Thomas

Damle

2004

37th AIAA Thermophysics Conference

View full text Add to dashboard Cite

The fully developed laminar flow within a re-entrant groove has been analyzed using a finite element model. Re-entrant grooves have been used in both axially-grooved heat pipes and in monogroove heat pipes. The main benefit to using this type of wick structure is the reduction of the liquid pressure drop along the length of the groove due to countercurrent liquid-vapor interaction at the meniscus. All previous researchers assumed that the pressure drop within the liquid could be modelled as flow within a smooth tube, but the results of the current analysis show that this assumption can lead to significant errors in the pressure drop prediction. An extensive literature survey was completed and the results of five previous studies were used to validate the current numerical model. It was found that the present finite element model is both more accurate and consumes less computer resources than a finite difference based model developed previously by one of the authors of the current manuscript. A parametric analysis was carried out to determine the Poiseuille number, Po = f Re, the dimensionless mean velocity, v * , and the dimensionless volumetric flow rate,V * , as functions of the geometry of the re-entrant groove (groove height 1.0 ≤ H * ≤ 4.0, slot half-width 0.05 ≤ W * /2 ≤ 0.9, fillet radius 0.0 ≤ R * f ≤ 1.0), and the liquid-vapor shear stress (0.0 ≤ −τ * lv ≤ 2.5). It was determined that the flow variables were strongly affected by the groove height, slot half-width and liquid-vapor shear stress, but were relatively unaffected by the fillet radius. The case in which the meniscus recedes into the re-entrant groove was examined, which could be a result of evaporator dry-out or insufficient liquid fill amount. The cross-sectional area of the liquid in the groove, A * l , the meniscus radius, R * m , and the above-mentioned flow variables were calculated as functions of the meniscus contact angle (0 • ≤ φ ≤ 40 • ) and meniscus attachment point (0.0 ≤ H * l ≤ 2.75). In general, the flow variables were more strongly affected by the meniscus attachment point than the meniscus contact angle. Finally, the results of the numerical model were used to determine the capillary limit of a low-temperature heat pipe with two different working fluids, water and ethanol, for a range of meniscus contact angles. The capillary limit heat transfer was found to attain a maximum value in the slot region and then decreased dramatically when the meniscus receded into the circular region of the re-entrant groove. NomenclatureA g = total cross-sectional area of the re-entrant groove, m = maximum mean liquid velocity, m/s v * = µv/R 2 (−dp/dy) v * = µv/R 2 (−dp/dy) V = volumetric flow rate, vA l , m 3 /ṡ V * = µV /[R 4 (−dp/dy)] W = width of the slot, m W * = W/R W l = width of the liquid meniscus at the attachment point to the re-entrant groove wall, m= width of the liquid meniscus at the attachment point to the sinusoidal groove wall, m W s = width of the sinusoidal groove, m W tr = width of the trapezoidal groove, m x, y, z = Carte...

show abstract

Theoretical Investigation of Advanced Capillary Structures in Grooved Heat Pipe Evaporators for Space Applications

Cited by 7 publications

References 6 publications

Experimental research of heat recuperators in ventilation systems on the basis of heat pipes

Experimental research of heat recuperators in ventilation systems on the basis of heat pipes

Fluid Flow in Axial Reentrant Grooves with Application to Heat Pipes

Analysis of Fluid Flow in Axial Re-entrant Grooves with Application to Heat Pipes

Contact Info

Product

Resources

About