The tribological characteristics of titanium nitride coatings. Part II. Comparisons of two deposition processes

Guu, Yeong Yan; Lin, Jen Fin

doi:10.1016/0043-1648(95)06631-4

Cited by 12 publications

(3 citation statements)

References 20 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…1a), where TiN thin film are deposited on AISI D6 at 220 o C, pores and white stains are distributed over the surface and white stains are found to be in a cluster form in the TiN matrix instead of uniform distribution. These white stains have been identified to be incompletely reactive titanium particle [7]. They are unable to form a strong bond in the grain boundary with the TiN matrix.…”

Section: Resultsmentioning

confidence: 99%

Characterisation of Titanium Nitride Thin Films Deposited by Cathodic Arc Plasma Technique on AISI D6 Tool Steel

Vieira

Nono²

2005

MSF

View full text Add to dashboard Cite

TiN thin film has been produced on the surface of AISI D6 tool steel by using a titanium interlayer. In this work, the morphology, the microstructure and interface depth profile of TiN films deposited at two substrate temperatures (220 oC and 450 oC) in the coating process are presented and discussed. The AISI D6 tool steel substrates were coated with titanium thin film as the underlayer and with TiN thin film as the top layer. They were deposited by conventional cathodic arc process. The surfaces of TiN films were observed by scanning electron microscopy (SEM). The microstructure of these samples was analysed by X-ray diffractometry (XRD). The influence of the substrate temperature on the TiN film-Ti film-AISI D6 interface region were investigated by energy dispersive spectrometry (EDS) and its cross section were observed using backscattered electron image (BEI). The results showed that TiN films deposited at 220 oC formed a film of strongly (111) preferred orientation, while in 450 oC formed a film of (111) and (220) preferred orientation. The thickness of the TiN films increased with increasing substrate temperature. The results show that the interface region of the TiN film-Ti film-AISI D6 substrate system was significantly improved when higher substrate temperature during deposition is used.

show abstract

Section: Resultsmentioning

confidence: 99%

Characterisation of Titanium Nitride Thin Films Deposited by Cathodic Arc Plasma Technique on AISI D6 Tool Steel

Vieira

Nono²

2005

MSF

View full text Add to dashboard Cite

show abstract

“…The white stains are found to be in a cluster form in the TiN matrix instead of uniform distribution. These white stains have been identified to be incompletely reactive titanium particles [9].…”

Section: Resultsmentioning

confidence: 99%

Microstructure and Interface Analyses of TiN Thin Films Deposited on M2 Speed Steel Substrate by Cathodic Arc Technique

Vieira

Nono²

2004

JMNM

View full text Add to dashboard Cite

TiN films with different substrate temperatures have been produced on the surface of M2 speed steel with a titanium interlayer by a cathodic arc plasma deposition process. In this work, the influence of the substrate temperature on the microstructure and interface depth profile of deposited titanium nitride (TiN) films by using a titanium interlayer are presented and discussed. The TiN film-Ti interlayer-M2 substrate interface region were analyzed by energy dispersive spectrometry (EDS) and were observed by backscattered electron image (BEI). The structure and morphology of the TiN film were evaluated using X-ray diffraction (XRD) and scanning electron microscopy (SEM). At lower temperature, the resultant TiN film exhibited strong (111) preferred orientation, whereas at higher temperature the dominant orientations of the film were ( 111) and ( 200). The result shows that the interface region of the TiN-Ti-M2 system was significantly improved at higher temperature.

show abstract

“…The tribological behavior and the wear mechanisms occurring in titanium nitride have been long studied [213][214] and the effects of various parameters such as substrates [215], coating thickness [216], and deposition methods [217] have been addressed. Some examples can be found in Fig.…”

Section: Wear Resistance Of Tin-based Coatings Deposited By Pvdmentioning

confidence: 99%

Wear resistance investigation of titanium nitride-based coatings

Santecchia

Hamouda

Musharavati

et al. 2015

Ceramics International

239

108

View full text Add to dashboard Cite

The tribological characteristics of titanium nitride coatings. Part II. Comparisons of two deposition processes

Cited by 12 publications

References 20 publications

Characterisation of Titanium Nitride Thin Films Deposited by Cathodic Arc Plasma Technique on AISI D6 Tool Steel

Characterisation of Titanium Nitride Thin Films Deposited by Cathodic Arc Plasma Technique on AISI D6 Tool Steel

Microstructure and Interface Analyses of TiN Thin Films Deposited on M2 Speed Steel Substrate by Cathodic Arc Technique

Wear resistance investigation of titanium nitride-based coatings

Contact Info

Product

Resources

About