“…In the mortars obtained epoxy resin was partially replaced (0-14% by weight) by poly(ethylene terephthalate) glycolysates. A detailed description pertaining to the selection of the plan is described in [Lichołai and Dębska 2014]. In the case of the research on chemical resistance, the plan took the form of a table (Table 1).…”
Resin concretes belong to a small group of building materials which, besides high strength parameters, also have a very good chemical resistance. This is confirmed by the studies carried out by various research institutions around the world. However, there is little data on the behaviour of composite resin exposed to corrosive solutions for an extended period of time. This article presents the results of the research on weight changes in samples of epoxy mortar modified with poly(ethylene terephthalate) glycolysates, immersed for 5 years in four different aggressive media i.e. 10% aqueous solutions of sulphuric and nitric acids, sodium hydroxide, and sodium chloride. The actual average weight changes obtained were compared with the data calculated on the basis of the regression functions fitted to the data recorded after 3.5 years of exposure. This allowed verification of the model selection correctness and evaluation of the effectiveness of the fitted regression curve. In the case of aqueous sodium hydroxide and sodium chloride solutions, it can be assumed that the logarithmic model describes weight changes well. It was observed that the weight of the samples exposed to NaCl solutions and NaOH stabilizes over prolonged monitoring time and reaches a plateau. However, the weight changes in mortar samples immersed for 5 years in aqueous solution of sulphuric and nitric acids quite significantly differ from the data calculated on the basis of the trend line fitted to the results of the tests carried out after 3.5 years of exposure. It seems that the better solution in this case is the selection of an exponential model. In addition, placing the logarithmic trendlines for all corrosive media together on a chart allows to note which of the solutions is the most aggressive. It was found that after 5 years of immersion in aqueous solutions of acids, mortar samples became brittle, and the observation of their fractures confirmed the weakness of the connection on the resin/aggregate phase boundary. Changes in the appearance of the samples were also noted, namely the surface of samples submerged in a solution of nitric acid strongly yellowed, and those treated with sulphuric acid were tarnished.
“…In the mortars obtained epoxy resin was partially replaced (0-14% by weight) by poly(ethylene terephthalate) glycolysates. A detailed description pertaining to the selection of the plan is described in [Lichołai and Dębska 2014]. In the case of the research on chemical resistance, the plan took the form of a table (Table 1).…”
Resin concretes belong to a small group of building materials which, besides high strength parameters, also have a very good chemical resistance. This is confirmed by the studies carried out by various research institutions around the world. However, there is little data on the behaviour of composite resin exposed to corrosive solutions for an extended period of time. This article presents the results of the research on weight changes in samples of epoxy mortar modified with poly(ethylene terephthalate) glycolysates, immersed for 5 years in four different aggressive media i.e. 10% aqueous solutions of sulphuric and nitric acids, sodium hydroxide, and sodium chloride. The actual average weight changes obtained were compared with the data calculated on the basis of the regression functions fitted to the data recorded after 3.5 years of exposure. This allowed verification of the model selection correctness and evaluation of the effectiveness of the fitted regression curve. In the case of aqueous sodium hydroxide and sodium chloride solutions, it can be assumed that the logarithmic model describes weight changes well. It was observed that the weight of the samples exposed to NaCl solutions and NaOH stabilizes over prolonged monitoring time and reaches a plateau. However, the weight changes in mortar samples immersed for 5 years in aqueous solution of sulphuric and nitric acids quite significantly differ from the data calculated on the basis of the trend line fitted to the results of the tests carried out after 3.5 years of exposure. It seems that the better solution in this case is the selection of an exponential model. In addition, placing the logarithmic trendlines for all corrosive media together on a chart allows to note which of the solutions is the most aggressive. It was found that after 5 years of immersion in aqueous solutions of acids, mortar samples became brittle, and the observation of their fractures confirmed the weakness of the connection on the resin/aggregate phase boundary. Changes in the appearance of the samples were also noted, namely the surface of samples submerged in a solution of nitric acid strongly yellowed, and those treated with sulphuric acid were tarnished.
“…85°C w ciągu 1 godziny. Zawartość modyfikatora w mieszaninie została dobrana w oparciu o przeprowadzone wcześniej badania kompozytów żywicznych [11]. W obydwu przypadkach jako utwardzacz zastosowano trietylenotetraaminę (Z-1).…”
Section: Użyte Surowce I Metody Otrzymywania Kompozycji żYwicznejunclassified
Swoiste właściwości żywic epoksydowych umożliwiają zaliczenie tych polimerów do grupy najlepszych materiałów klejowych. O wyższości klejów epoksydowych decyduje m.in. ich doskonała przyczepność do łączonych powierzchni oraz bardzo dobra odporność chemiczna. Ich stosowanie jest ułatwione poprzez moż-liwość prowadzenia procesu utwardzania z zastosowaniem jedynie nacisku zapewniającego dokładne przyleganie powierzchni łączonych. Złącze epoksydowe może niekiedy zastąpić takie sposoby łączenia, jak nitowanie lub spawanie. Fakt ten jest szczególnie ważny w tych zastosowaniach, gdzie wymagana jest duża gładkość powierzchni. Istotna jest także możliwość łączenia ze sobą rożnych materiałów np. metali, szkła, ceramiki, betonu, tworzyw sztucznych oraz gumy. Modyfikowane kleje epoksydowe o zwiększonej elastyczności stanowią doskonałe rozwiązanie w przypadku różnic we współczynnikach rozszerzalności materiałów łączonych i utwardzonej żywicy. W pracy opisano przeprowadzone badania żywi-cy epoksydowej Epidian 5 oraz kompozycji tej samej żywicy częściowo zastąpio-nej przez glikolizat odpadowego poli(tereftalanu etylenu) (PET). Porównano wybrane właściwości otrzymanych kompozycji, pod kątem możliwości ich aplikacji jako głównego składnika klejów budowlanych. Wykazano, że zaproponowana kompozycja epoksydowa odznacza się korzystnymi właściwościami mechanicznymi, a jednocześnie zastosowany modyfikator pełni rolę substancji poprawiają-cej elastyczność spoiny klejowej. Dodatkowo, modyfikator obniża koszty produkcji klejów, które postrzegane są za stosunkowo drogie. Wykorzystanie materiałów pochodzących z recyklingu (odpadowy PET) jako modyfikatorów klejów epoksydowych stwarza możliwości udoskonalenia cech technicznych tych materiałów, dając jednocześnie znaczące korzyści środowiskowe.Słowa kluczowe: odpady PET, właściwości mechaniczne, elastyczność spoiny, kleje epoksydowe
WprowadzenieKleje są to substancje, będące w stanie ciekłym które po wprowadzeniu pomiędzy dwie powierzchnie wykazują zdolność do trwałego połączenia tych elementów. Proces łączenia zachodzi w wyniku działania sił adhezji kleju do powierzchni klejonej oraz sił spójności wewnętrznej działających w warstwie kleju (kohezja). Klej powinien charakteryzować się dużą przyczepnością do podłoża i trwałością złącza, jednocześnie nie powodując zmian kształtu ani innych właściwości materiałów łączonych [1].W budownictwie pierwsze substancje klejące stosowano do łączenia róż-nych materiałów już kilka tysięcy lat temu. Wykorzystywano wtedy siłę klejącą naturalnych substancji "kleistych", m.in. białka, kazeiny zawartej w mleku, czy żywicy wydzielanej przez niektóre rośliny. Obecnie, ogromne znaczenie klejów wynika przede wszystkim z szerokiego rozpowszechnienia substancji wielkocząsteczkowych, czyli polimerów [2]. Polimer jako podstawowy składnik kleju nadaje mu unikalną budowę wewnętrzną, a tym samym zdolność do klejenia. Jednocześnie dzięki obecności polimerów uzyskuje się pożądaną przyczepność kleju do sklejanych powierzchni. Polimery nadają także spoinie odpowiednią wytrzyma...
“…The plan of the experiment that was chosen assumed a repetition of the investigation in the central point and that is why points 5 and 6 of the plan do not differ in their composition. The precise criteria connected with the choice of the plan of the experiment and its analysis are described in articles [25,26]. …”
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.