The influence of microporosity on the ductility of Al/Al2O3 alloys

Kellerer, H.; Piatti, G.

doi:10.1007/bf00585490

Cited by 15 publications

(8 citation statements)

References 3 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Fig. 6, which reports in addition to the new data on A1-0.7 % A1203, data for 4, 7 and 14 ~ A1-A1208 alloys [1 ], shows that at 450 ~ C the density variation is not proportional to the oxide content, but changes rapidly at low concentrations and remains practically constant at high oxide values. The oxide distribution is generally intergranular in our alloys, while in the SAP alloys it is also intragranular.…”

mentioning

confidence: 90%

“…At high temperature a high rate of crackformation was found. It was observed [1] that the extent of cavitation as measured by a density change, increased slightly with increasing alumina content (from 4 to 14 wt ~ AlcOa), following an irregular trend at different temperatures. In the present work comparative experiments were carried out on pure aluminium and slightly oxidised aluminium.…”

mentioning

confidence: 92%

“…In previous work [1][2][3] the influence of temperature on strain-induced cavitation in AI-AI~Oa (SAP) alloys was studied after tensile and creep tests. At high temperature a high rate of crackformation was found.…”

mentioning

confidence: 99%

See 2 more Smart Citations

Density measurements after tensile and creep tests on pure and slightly oxidised aluminium

Beghi¹,

Geel²,

Piatti³

1970

J Mater Sci

Self Cite

View full text Add to dashboard Cite

In order to investigate the influence of dispersed oxide particles on crack-formation in AI-AI2Oa alloys, series of tensile tests (20 to 550 ~ C) and creep tests (450 ~ C) were carried out on pure AI and on AI-0.7 wt~ AI203 specimens. Density measurements performed on broken samples showed no changes in pure AI but considerable decreases in the slightly oxidised AI. The observed influence of oxide is strong for the small percentage if compared with the behaviour of AI-AI203 alloys with much higher oxide contents.In previous work [1-3] the influence of temperature on strain-induced cavitation in AI-AI~Oa (SAP) alloys was studied after tensile and creep tests. At high temperature a high rate of crackformation was found. It was observed [1] that the extent of cavitation as measured by a density change, increased slightly with increasing alumina content (from 4 to 14 wt ~ AlcOa), following an irregular trend at different temperatures. In the present work comparative experiments were carried out on pure aluminium and slightly oxidised aluminium.The materials used were obtained from high purity aluminium ingots (A1 99.99%) extruded into bars of 20 mm diameter (temperature 500 ~ C, extrusion ratio _~ 12). Some of these bars were utilised for the pure A1 samples: average measured density 2.6984 g cm -a. For the preparation of the oxidised material the remaining bars were swaged to a diameter of 2 ram, and oxyacetylene sprayed in air to obtain a slightly oxidised powder. This powder (dimension of particles < 200Fro) was subsequently hotpressed and extruded (temperature 500 ~ C, extrusion ratio _ 12) into bars of 20 mm diameter. Average measured density for this oxidised material: 2.6946 g cm -a.Chemical analysis showed the sprayed material to have an oxide content of 0.70 wt ~. The theoretical density of this material cannot be stated because of uncertainty of the density of the alumina. The oxide was present in the form (A L C O A denomination) as determined by 9 1970 Chapman and Hall Ltd.X-ray diffraction on the alumina extracted from the matrix; the method is described in [4]. The alumina powder, after extraction, was also examined by electron microscopy; the morphology was similar to that of aluminium oxide extracted by the same method from SAP alloys.The tensile and creep specimens for both the oxidised and pure aluminium material had a gauge length of 50 mm with diameter 10 ram. For both materials two series of experiments were carried out: (a) Tensile tests at different temperatures from 20 to 600~ cross-head speed of 3 mm rain -1 (strain rate 1.0 • 10 -~ sec-1). (b) Accelerated creep tests with constant load at 450 ~ C at different levels. Density measurements were carried out by the immersion technique according to the method described in [2]. Microscopical examination was carried out on several specimens in order to follow eventual grain growth during the experiments.In fig. 1 the ultimate tensile strength and the total elongation are plotted against the temperature. The results for the total elongation are rath...

show abstract

mentioning

confidence: 90%

mentioning

confidence: 92%

See 1 more Smart Citation

Density measurements after tensile and creep tests on pure and slightly oxidised aluminium

Beghi¹,

Geel²,

Piatti³

1970

J Mater Sci

Self Cite

View full text Add to dashboard Cite

show abstract

“…[1] During the diffusion process, normally no liquid phase is formed. [1] During the diffusion process, normally no liquid phase is formed.…”

Section: Introductionmentioning

confidence: 99%

Considerations of Microstructural Influences for Diffusion Welding of Metals in Microsystem Technology

et al. 2013

View full text Add to dashboard Cite

Diffusion welding is a special high‐tech solid joining technique. Most research was done and publications were written in the years between 1970 and 1980. The aim of this paper is to take a closer look at the fundamental processes inside the material during diffusion welding and to discuss the relation between the materials microstructure for diffusion processes from a material science point of view. For this, it is necessary to discuss the impact of different lattice defects and to observe the intrinsic energetically conditions of a metal originating from its delivery state and manufacturing history, as well as its surface condition. In particular, emphasis is paid to the special requirements for joining of micro process devices.

show abstract

“…Gasporen zwischen den sich verschweiBenden Oberflachenrauhigkeiten eingeschlossen werden konnen. Ahnliches ist bei Sintermaterialien beobachtet worden[13]. In diesen sich wahrend des DS-Vorganges noch verkleinernden Poren konnen unter Umstanden erhebliche Drucke auftreten.…”

unclassified

Das Diffusionsschweißen von Titanlegierungen

Kellerer

1972

Materialwissenschaft Werkst

View full text Add to dashboard Cite

show abstract

The influence of microporosity on the ductility of Al/Al2O3 alloys

Cited by 15 publications

References 3 publications

Density measurements after tensile and creep tests on pure and slightly oxidised aluminium

Density measurements after tensile and creep tests on pure and slightly oxidised aluminium

Considerations of Microstructural Influences for Diffusion Welding of Metals in Microsystem Technology

Das Diffusionsschweißen von Titanlegierungen

Contact Info

Product

Resources

About