The effect of sandblasting on surface properties for adhesion

Rudawska, Anna; Danczak, Izabela; Müller, Miroslav; Valášek, Petr

doi:10.1016/j.ijadhadh.2016.06.010

Cited by 128 publications

(82 citation statements)

References 54 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…The value of surface free energy (SFE) was determined by means of the Owens-Wendt method calculated on the basis of the wetting measurements of the examined surfaces. The whole analysis for determining the surface free energy uncertainty by means of the Owens-Wendt method (also known as the Owens-Wendt method) was shown by Rudawska [28,29].…”

Section: Surface Measurementsmentioning

confidence: 99%

See 1 more Smart Citation

Fracture Analysis and Shear Strength of Aluminum/CFRP and GFRP Adhesive Joint in Fiber Metal Laminates

Ostapiuk

Bieniaś

2019

Materials

View full text Add to dashboard Cite

Fiber metal laminates (FMLs) were initially developed under the motivation of the aerospace industry. Generally, they consist of aluminum and high strength glass fiber in polymeric layers, but the new challenge is to apply them with a carbon fiber. Pretreatment of aluminum is the main factor responsible for the adhesion between metallic and polymeric layers. The shear strength test a very popular method in the experimental joint of two components. In this article, the main aim was to compare the surface pretreatment and configuration of fibers in FMLs based on aluminum with glass and carbon fibers. The decisive factor of strength in adhesive or cohesive failure is first the type of fibers, and second, the surface preparation.

show abstract

Section: Surface Measurementsmentioning

confidence: 99%

“…The schematic sample view and profile with dimensions are shown in Figure 2. uncertainty by means of the Owens-Wendt method (also known as the Owens-Wendt method) was shown by Rudawska [28,29].…”

Section: Shear Strength Testmentioning

confidence: 99%

Fracture Analysis and Shear Strength of Aluminum/CFRP and GFRP Adhesive Joint in Fiber Metal Laminates

Ostapiuk

Bieniaś

2019

Materials

View full text Add to dashboard Cite

show abstract

“…Do grupy 1 należą metody, których celem jest rozwinięcie powierzchni, co zwykle jest też związane z uzyskaniem powierzchni chropowatej, czego efektem jest zwiększony udział adhezji mechanicznej. Rozwinięcie powierzchni jest zwykle realizowane przy udziale mechanicznych metod obróbki powierzchni narzędziami nasypowymi lub metodami obróbki Zbigniew Zimniak, Roman Wróblewski przeglad Welding Technology Review strumieniowo-ściernej [6,9]. Niestety należą one do metod pracochłonnych i komplikujących proces wytwórczy.…”

Section: Wstępunclassified

Wpływ aktywacji powierzchni aluminium 7075 na wytrzymałość połączenia klejowego

Zimniak

Wróblewski

2018

Przegląd Spawalnictwa

View full text Add to dashboard Cite

show abstract

“…Apart from other influencing factors like adherend material, geometric design of the bond line and its loading conditions, the adhesive properties significantly impact the strength of an adhesive bond [3,6,7,9,13,24]. The strength of adhesive joints is affected by a number of technological factors [4,8,12,18,19,20,23], e.g. proper surface treatment, adhesive preparation, temperature and loading conditions during cure, and a few structural factors [1,2,15,21], such as the type and thickness of adherends, overlap length, the type of joint, adhesive layer thickness.…”

Section: Introductionmentioning

confidence: 99%

The Influence of Selected Factors on the Strenght of Wood Adhesive Joints

Rudawska¹,

Maziarz²,

Šajgalík³

et al. 2018

Adv. Sci. Technol. Res. J.

Self Cite

View full text Add to dashboard Cite

This paper examines the effect of selected factors on the wood bonded joint strength. The structural factor under scrutiny was the geometry of the surface area; however, other major dimensions of adherends were compared as well. The tests were performed on 6 joint types: butt, v-shaped, interlocking, scarf, tongue & groove, and single lap joints, which were formed on two types of substrate materials-pine and oak wood, and adhesively bonded. The joints were bonded with Prefere 6312 wood adhesive and Loctite 3430 two-component epoxy adhesive. Strength testing of the joints was performed on Zwick/Roell Z150 material testing machine, according to DIN EN 1465 standard. The results obtained from the tests indicate that bonded joints of oak wood exhibit higher strength properties than those of pine wood adherends, which was confirmed in nearly all strength tests.

show abstract

The effect of sandblasting on surface properties for adhesion

Cited by 128 publications

References 54 publications

Fracture Analysis and Shear Strength of Aluminum/CFRP and GFRP Adhesive Joint in Fiber Metal Laminates

Fracture Analysis and Shear Strength of Aluminum/CFRP and GFRP Adhesive Joint in Fiber Metal Laminates

Wpływ aktywacji powierzchni aluminium 7075 na wytrzymałość połączenia klejowego

The Influence of Selected Factors on the Strenght of Wood Adhesive Joints

Contact Info

Product

Resources

About