The effect of heat treatment on pseudoelastic behavior of spark plasma sintered NiTi

Ozerim, Gulcan; Anlaş, Günay; Moumni, Ziad

doi:10.1016/j.mtcomm.2022.103819

Cited by 2 publications

(1 citation statement)

References 41 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Compared with the specimens with the Nb addition, a higher content of the Ni-rich phase appears in the Nb0 specimen. For the specimens with Ni content higher than 50.5 at.%, the solution treatment can make part of the Ni 3 Ti phase re-dissolve in the NiTi phase [ 17 , 18 ]. However, in the subsequent aging treatment at 450 °C, the Ni-rich phase precipitates again as the Ni 4 Ti 3 phase [ 19 ].…”

Section: Resultsmentioning

confidence: 99%

Effect of Nb on the Damping Property and Pseudoelasticity of a Porous Ni-Ti Shape Memory Alloy

et al. 2023

View full text Add to dashboard Cite

In order to develop novel high damping materials with excellent pseudoelasticity (PE) properties to meet the application requirements in aerospace, medical, military and other fields, porous Ni50.8Ti49.2 shape memory alloy (SMA) was prepared by the powder metallurgy method. Different contents of Nb element were added to regulate the microstructures. It was found that after adding the Nb element, the number of precipitates significantly decreased, and the Nb element was mainly distributed in the Ni-Ti matrix in the form of β-Nb blocks surrounded by Nb-rich layers. Property tests showed that with the increase in Nb content, the damping and PE increased first and then decreased. When the Nb content reached 9.0 at.%, the highest damping and the best PE could be achieved. Compared with the porous Ni-Ti SMA without Nb addition, the damping and PE increased by 60% and 35%, respectively. Correlated mechanisms were discussed.

show abstract

Section: Resultsmentioning

confidence: 99%

Effect of Nb on the Damping Property and Pseudoelasticity of a Porous Ni-Ti Shape Memory Alloy

et al. 2023

View full text Add to dashboard Cite

show abstract

Investigation of the Effect of Sintering Temperatures on the Production of Porous Niti Alloy by Loosen Sintering Method

Tanış

Bostan²

2022

IJERAD

View full text Add to dashboard Cite

This article aims to produce NiTi shape memory alloys, which show superelasticity and shape memory effect, as well as good biocompatibility and corrosion properties, in open and porous sizes ranging from 100-500 μm, which are required for use as implants. This structure of pores is necessary to allow tissue growth and fluid flow inside the implants. Many powder metallurgy methods have been used in producing porous NiTi shape memory alloys. However, the packaging pressure used in these methods has not successfully created the desired pore distribution, shape, and size. The methods by which it can be produced are costly in terms of cost. In the study, production was carried out by sintering the powder mixture poured into molds without pressure with the help of binder polymers. This sintering process was carried out in an argon atmosphere for 1 hour at temperatures 1050, 1125, and 1200 °C. The study shows that pressureless loosen sintering can produce porous NiTi alloys, which is the more straightforward method. The pore distribution and proportions were examined. Homogeneous distribution and pores in desired sizes are created. It has also been determined that the binder polymer has a space-retaining effect. It was determined at which temperature the alloy sintered at different temperatures contained the desired B2 austenite phase for superelasticity. Austenite start and finish temperatures were determined for the alloy produced at each sintering temperature. As a result of this research, it was determined which phase was denser at which temperature, and the phase transformation temperatures were found. The exact temperature measurements can be calculated by changing the sintering time parameter. In addition, the change in phase transformation temperatures can be measured by heat treatment after sintering. Porous NiTi alloys can be used as dental and medical implants thanks to their excellent biocompatibility and corrosion resistance. This method will decrease production costs, and more people will have access to this material. In general, the mechanism of sintering methods is joining the points in contact with the packaging pressure by necking. In this study, the combination of the grains with the polymer without packaging pressure with the thermal expansion mechanism reveals the originality of the study.

show abstract

The effect of heat treatment on pseudoelastic behavior of spark plasma sintered NiTi

Cited by 2 publications

References 41 publications

Effect of Nb on the Damping Property and Pseudoelasticity of a Porous Ni-Ti Shape Memory Alloy

Effect of Nb on the Damping Property and Pseudoelasticity of a Porous Ni-Ti Shape Memory Alloy

Investigation of the Effect of Sintering Temperatures on the Production of Porous Niti Alloy by Loosen Sintering Method

Contact Info

Product

Resources

About