The effect of external compressive loads on the cycle lifetime of lithium-ion pouch cells

Barai, Anup; Tangirala, Ravichandra; Uddin, Kotub; Chevalier, J.; Guo, Yue; McGordon, Andrew; Jennings, Paul

doi:10.1016/j.est.2017.07.021

Cited by 78 publications

(33 citation statements)

References 32 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Cells with initial external pressures have longer life than those without initial external pressures. Barai et al 24 of Warwick University compared the cycle life and power performance of 15 Ah NCM lithium‐ion pouch cells under three different confinement pressures. After 1200 cycles, the capacity fading of cells at 0, 5 and 15 psi pressure is 11.0%, 8.8% and 8.4% respectively, and the corresponding power fading is 7.5%, 39%, and 18% respectively.…”

Section: Introductionmentioning

confidence: 99%

A study of external surface pressure effects on the properties for lithium‐ion pouch cells

et al. 2020

View full text Add to dashboard Cite

Summary Lithium‐ion pouch cells are widely used in electric vehicles because of their high energy density than other structures. There is an unavoidable external surface pressure between the cells in the process of packing and driving of electric vehicles. The influence of external surface pressure on the main properties of the lithium‐ion pouch cell has been studied, which is of great significance to packing batteries and reusing retired cells. In this study, a testing device applied for the measurement of constant external surface pressures of lithium‐ion pouch cells was first proposed and the different pressure stress‐strain distribution on the external surface of cells under semirigid material pads were analyzed by simulation. The effects of pressure on the capacity, internal resistance, and open circuit voltage of fresh and aged LiNixCoyMnzO2 (NCM) lithium‐ion pouch cells are analyzed through experiments under 1 Mpa external surface pressure. The results show that the internal resistance of fresh cells tends to decrease. The average percentage of the maximum reduction of internal resistance is 13.28%. The experiments also demonstrate that the capacity of aging cells increased by 2.3%. Irreversibility of capacity improvement indicates applying appropriate external surface pressure can improve the secondary utilization efficiency of aging cells.

show abstract

Section: Introductionmentioning

confidence: 99%

A study of external surface pressure effects on the properties for lithium‐ion pouch cells

et al. 2020

View full text Add to dashboard Cite

show abstract

“…The effect of compressive pressure on battery degradation was investigated. Battery cells were cycled 1200 times under 0.5 psi and 15 psi compressive pressure loads [11]. It was seen that capacity fade for 0.5 and 15 psi pressure loads were 11.0%, 8.8%, and 8.4%.…”

Section: Effect On Capacitymentioning

confidence: 99%

“…This contradictory behavior was found to be pertaining to the separator creep and wettability rise in the cell after pressure load was applied. The investigation determined the progress of compressive loads over numerous cycles, and it was concluded that pressure raises with cycling [11].…”

Section: Effect On Capacitymentioning

confidence: 99%

Characterization of the Compressive Load on a Lithium-Ion Battery for Electric Vehicle Application

2021

View full text Add to dashboard Cite

Lithium-ion batteries are being implemented in different large-scale applications, including aerospace and electric vehicles. For these utilizations, it is essential to improve battery cells with a great life cycle because a battery substitute is costly. For their implementation in real applications, lithium-ion battery cells undergo extension during the course of discharging and charging. To avoid disconnection among battery pack ingredients and deformity during cycling, compacting force is exerted to battery packs in electric vehicles. This research used a mechanical design feature that can address these issues. This investigation exhibits a comprehensive description of the experimental setup that can be used for battery testing under pressure to consider lithium-ion batteries’ safety, which could be employed in electrified transportation. Besides, this investigation strives to demonstrate how exterior force affects a lithium-ion battery cell’s performance and behavior corresponding to static exterior force by monitoring the applied pressure at the dissimilar state of charge. Electrochemical impedance spectroscopy was used as the primary technique for this research. It was concluded that the profiles of the achieved spectrums from the experiments seem entirely dissimilar in comparison with the cases without external pressure. By employing electrochemical impedance spectroscopy, it was noticed that the pure ohmic resistance, which is related to ion transport resistance of the separator, could substantially result in the corresponding resistance increase.

show abstract

“…To investigate effects from macroscopic external and internal mechanical loads such as vibrations [24,25], shocks [24,26] and crush [27,28], a variety of simulative approaches have been conducted in the past, but only a few have investigated mechanical pressure on cell level [16,19,29,30]. Most publications use a homogenized model of the electrode stack, but only a few present electrode layerresolved mechanical models as shown by the review of Kermani et al [31].…”

Section: Introductionmentioning

confidence: 99%

Simulation of Spatial Strain Inhomogeneities in Lithium-Ion-Cells Due to Electrode Dilation Dependent on Internal and External Cell Structures

Ebert¹,

Spielbauer²,

Bruckmoser³

et al. 2021

Preprint

View full text Add to dashboard Cite

Electrochemical-mechanical interactions, in particular pressure-induced ones, have been identified to be a cause for lithium-plating in lithium-ion cells. Mechanically-induced porosity inhomogeneities in the separator layers due to electrode expansion during charging especially lead to cell internal balancing currents and can cause localized plating. To identify cell-format and cell-material dependent mechanical weak spots, a layer-resolved mechanical simulation of different cell types and cell-material combinations is presented in this work. The simulation results show distinctive layer strain patterns for different cell-types that coincide with localized lithium-plating found in post-mortem cells. Additionally, the effects of cell bracing in battery modules is investigated and a method to mitigate the increased layer strain due to bracing counterforces is proposed that also increases cell energy density for hardcase-type automotive cells.

show abstract

The effect of external compressive loads on the cycle lifetime of lithium-ion pouch cells

Cited by 78 publications

References 32 publications

A study of external surface pressure effects on the properties for lithium‐ion pouch cells

A study of external surface pressure effects on the properties for lithium‐ion pouch cells

Characterization of the Compressive Load on a Lithium-Ion Battery for Electric Vehicle Application

Simulation of Spatial Strain Inhomogeneities in Lithium-Ion-Cells Due to Electrode Dilation Dependent on Internal and External Cell Structures

Contact Info

Product

Resources

About