The clarification of α″ phase precipitate from β phase in Ti-15Mn alloy by mismatch theory

Zhang, Haoyin; Liu, Xingjun; Yang, Shuiyuan; Jiang, Hengxing; Shi, Zhan; Yang, Mujin; Wang, Cuiping

doi:10.1016/j.matlet.2017.05.032

Cited by 8 publications

(2 citation statements)

References 12 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…This resulted from the slower cooling rate in the HT-ed alloy than in the SLM-ed alloy. The orientation relationship between the β and α phases is presented by: [113] β //[1−210] α , as reported by Zhang et al 26 and Wan et al 27 The high-resolution TEM image presented the interface between a BCC and HCP structures ( Fig. 6f ), further confirmed the orientation relationship.…”

Section: Resultssupporting

confidence: 82%

Multi-scale microstructure high-strength titanium alloy lattice structure manufactured via selective laser melting

Yang

et al. 2021

RSC Adv.

View full text Add to dashboard Cite

show abstract

Section: Resultssupporting

confidence: 82%

Multi-scale microstructure high-strength titanium alloy lattice structure manufactured via selective laser melting

Yang

et al. 2021

RSC Adv.

View full text Add to dashboard Cite

show abstract

“…At the same time, the supersaturated α′ and α″ martensites show a need-like structure. Finally, different studies conducted by [ 258 , 259 , 261 , 263 , 264 ] reported the following crystallographic relationships among all microstructures present in as-built Ti6Al4V samples:

…”

Section: L-pbfed Ti6al4v: Microstructurementioning

confidence: 98%

Additive Manufacturing of AlSi10Mg and Ti6Al4V Lightweight Alloys via Laser Powder Bed Fusion: A Review of Heat Treatments Effects

Ghio

Cerri

2022

Materials

View full text Add to dashboard Cite

Laser powder bed fusion (L-PBF) is an additive manufacturing technology that is gaining increasing interest in aerospace, automotive and biomedical applications due to the possibility of processing lightweight alloys such as AlSi10Mg and Ti6Al4V. Both these alloys have microstructures and mechanical properties that are strictly related to the type of heat treatment applied after the L-PBF process. The present review aimed to summarize the state of the art in terms of the microstructural morphology and consequent mechanical performance of these materials after different heat treatments. While optimization of the post-process heat treatment is key to obtaining excellent mechanical properties, the first requirement is to manufacture high quality and fully dense samples. Therefore, effects induced by the L-PBF process parameters and build platform temperatures were also summarized. In addition, effects induced by stress relief, annealing, solution, artificial and direct aging, hot isostatic pressing, and mixed heat treatments were reviewed for AlSi10Mg and Ti6AlV samples, highlighting variations in microstructure and corrosion resistance and consequent fracture mechanisms.

show abstract

Molecular Dynamics Simulation of the Tensile Deformation Behavior of the γ(TiAl)/α2(Ti3Al) Interface at Different Temperatures

Liu

Zhang

2021

J. of Materi Eng and Perform

View full text Add to dashboard Cite

The clarification of α″ phase precipitate from β phase in Ti-15Mn alloy by mismatch theory

Cited by 8 publications

References 12 publications

Multi-scale microstructure high-strength titanium alloy lattice structure manufactured via selective laser melting

Multi-scale microstructure high-strength titanium alloy lattice structure manufactured via selective laser melting

Additive Manufacturing of AlSi10Mg and Ti6Al4V Lightweight Alloys via Laser Powder Bed Fusion: A Review of Heat Treatments Effects

Molecular Dynamics Simulation of the Tensile Deformation Behavior of the γ(TiAl)/α2(Ti3Al) Interface at Different Temperatures

Contact Info

Product

Resources

About