Synthesis, XRD single crystal structure analysis, vibrational spectral analysis, molecular dynamics and molecular docking studies of 2-(3-methoxy-4-hydroxyphenyl) benzothiazole

Devi, A. Sarau; Aswathy, V.V.; Mary, Y. Sheena; Panicker, C. Yohannan; Armaković, Stevan; Ravindran, Reena; Alsenoy, C. Van

doi:10.1016/j.molstruc.2017.07.065

Cited by 17 publications

(1 citation statement)

References 70 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…As presented in Scheme 1, the starting materials: 4-(benzo[d]thiazol-2-yl)-2-methoxyphenol (1) (0.41 g, 1.58 mmol) synthesized according to literature [35] and commercially purchased 4-nitrophthalonitrile (2) (0.27 g, 1.58 mmol) were mixed in dry DMF (20 mL) to derive 4-(4-benzo[d]thiazole-2-yl)-2-methoxyphenoxy) phthalonitrile (3). After half an hour, dry K 2 CO 3 (0.54 g, 3.94 mmol) was added to this mixture in eight portions.…”

Section: Synthesis and Characterization Of Copper (Ii) Phthalocyaninementioning

confidence: 99%

Immobilized TiO2/ZnO Sensitized Copper (II) Phthalocyanine Heterostructure for the Degradation of Ibuprofen under UV Irradiation

et al. 2021

View full text Add to dashboard Cite

Photocatalytic coatings of TiO2/ZnO/CuPc were developed on stainless steel substrates by subsequent sol gel dip coating for TiO2, spray pyrolysis for ZnO, and spin coating for copper (ii) phthalocyanine (CuPc) deposition. The latter compound was successfully prepared using a Schiff-based process. The materials and coatings developed were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy with attached energy dispersive spectroscopy (SEM-EDS), UV-Vis spectroscopy, room temperature photoluminescence (RTPL) spectroscopy, H1-nuclear magnetic resonance (1H-NMR) spectroscopy, C13-nuclear magnetic resonance (13C-NMR) spectroscopy, and matrix-assisted laser desorption/ionization-time of flight (MALDI-TOF) mass spectrometry (MS). The as-deposited TiO2/ZnO/CuPc on stainless steel retained in pristine state the structural and morphological/spectroscopic characteristics of its respective components. Estimated energy band gap values were 3.22 eV, 3.19 eV, 3.19 eV for TiO2, ZnO, TiO2/ZnO respectively and 1.60 eV, 2.44 eV, and 2.92 eV for CuPc. The photocatalytic efficiency of the fabricated TiO2/ZnO/CuPc coatings was tested toward ibuprofen (IBF). After 4 h irradiation under 365 nm UV, an increased degradation of about 80% was achieved over an initial 5 mg/L ibuprofen (IBF). This was much higher compared to about 42% and 18% IBF degradation by TiO2/ZnO and TiO2 thin film, respectively. In all cases, the stability of the best-performing photocatalyst was investigated showing a small decline to 77% of IBF degradation after the 5th cycle run. The effect of pH, reactive oxygen species (ROS) probe, shed light on a possible catalytic mechanism that was suggested.

show abstract

Section: Synthesis and Characterization Of Copper (Ii) Phthalocyaninementioning

confidence: 99%