Synthesis of a functionalized carbon supported platinum–iridium nanoparticle catalyst by the rapid chemical reduction method for the anodic reaction of direct methanol fuel cells

Bekmezci, Muhammed; Subasi, Deniz Belkıs; Bayat, Ramazan; Akin, Merve; Coguplugil, Zeynep Kazel; Şen, Fatih

doi:10.1039/d2nj03209k

Cited by 17 publications

(5 citation statements)

References 39 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Then, Pd@TiO 2 was dried in an oven at 50 °C. [11,40,41] The same procedures were carried out for the synthesis of the Pd electrocatalyst using only PdCl 2 .…”

Section: Methodsmentioning

confidence: 99%

“…[9,10] To overcome these problems and to increase the catalytic activity of electrocatalysts, the use of support materials is one of the most important issues. [10] As support material in AOR studies, It is seen that structures such as carbon allotropes, [11] carbides, metal oxides, or nanofibers are mostly used. Among these structures, nanofibers are one-dimensional nanostructures, and such structures can exhibit a high surface/volume ratio, small pore size, mechanical, and superior electronic properties.…”

mentioning

confidence: 99%

See 1 more Smart Citation

Facile Synthesis of Fiber‐Reinforced Catalyst for High Performance Ethanol and 2‐Propanol Oxidation

Bayat,

Akin,

Bekmezci

et al. 2024

Energy Tech

Self Cite

View full text Add to dashboard Cite

In this study, Pd@TiO2 nanostructure is formed by using TiO2 fibers obtained by the electrospinning method and chemical reduction method, and this nanostructure is used in C2, and C3 alcohol oxidation studies as an application. In addition, TiO2 is compared with the Pd catalyst to investigate the effect of TiO2. In the results obtained, peak current values of 193 and 66.7 mA cm−2 for ethanol oxidation and 127.38 and 36.18 mA cm−2 for 2‐propanol oxidation are observed for Pd@TiO2 and Pd catalysts, respectively. With the addition of TiO2 to the structure, the electrocatalytic activity of C2 and C3 alcohol oxidations increases 3–3.5 times and contributes to the onset potential at an earlier potential. It also shows higher durability and stability in long‐term tests. Moreover, the addition of TiO2 to the structure enhances the electrocatalytic activity and provides high current density and long‐term stability in alcohol oxidation. These results show that fibrous structures in combination with metals improve the effect of catalysts and exhibit high potential for their application in alcohol fuel cells.

show abstract

“…Then, Pd@TiO 2 was dried in an oven at 50 °C. [11,40,41] The same procedures were carried out for the synthesis of the Pd electrocatalyst using only PdCl 2 .…”

Section: Methodsmentioning

confidence: 99%

mentioning

confidence: 99%

Facile Synthesis of Fiber‐Reinforced Catalyst for High Performance Ethanol and 2‐Propanol Oxidation

Bayat,

Akin,

Bekmezci

et al. 2024

Energy Tech

Self Cite

View full text Add to dashboard Cite

show abstract

“…Bekmezci et al synthesized carbon-supported PtIr NPs. [133] The hydrogen oxidation reaction (HOR) peak current density was calculated to be 61.98 mA cm −2 . The PtIr catalyst also had higher ECSA and CO poisoning tolerance, than C-Pt.…”

Section: Pt-irmentioning

confidence: 99%

Catalyst Development for High‐Temperature Polymer Electrolyte Membrane Fuel Cell (HT‐PEMFC) Applications

Šešelj¹,

Alfaro²,

Bompolaki³

et al. 2023

Advanced Materials

View full text Add to dashboard Cite

A constant increase in global emission standard is causing fuel cell (FC) technology to gain importance. Over the last two decades, a great deal of research has been focused on developing more active catalysts to boost the performance of high‐temperature polymer electrolyte membrane fuel cells (HT‐PEMFC), as well as their durability. Due to material degradation at high‐temperature conditions, catalyst design becomes challenging. Two main approaches are suggested: (i) alloying platinum (Pt) with low‐cost transition metals to reduce Pt usage, and (ii) developing novel catalyst support that anchor metal particles more efficiently while inhibiting corrosion phenomena. In this comprehensive review, the most recent platinum group metal (PGM) and platinum group metal free (PGM‐free) catalyst development is detailed, as well as the development of alternative carbon (C) supports for HT‐PEMFCs.

show abstract

“…4,5 Due to the problems of H 2 as a fuel in proton-exchange membrane fuel cells (PEMFCs), such as its transportation and storage, in recent years, researchers have focused on direct liquid fuel cells (DLFCs). Different liquid fuels can be used in DLFCs, 6 such as ethanol, [7][8][9] methanol, [10][11][12] borohydride, 13,14 hydrazine, [15][16][17] and formate. 18,19 Ethanol oxidation has more steps than the methanol oxidation reaction.…”

Section: Introductionmentioning

confidence: 99%

Nitrogen-doped graphene quantum dots as a support for Ni–Au nanoparticles: efficient electrocatalysts for ethanol and formate fuel cells using hydrogen peroxide as an oxidant

Chalani,

Hosseini,

Abrari

et al. 2024

New J. Chem.

View full text Add to dashboard Cite

show abstract

Synthesis of a functionalized carbon supported platinum–iridium nanoparticle catalyst by the rapid chemical reduction method for the anodic reaction of direct methanol fuel cells

Abstract: Direct methanol fuel cells (DMFCs) stand out among the most common technologies in energy storage and are environmentally friendly energy converters that convert chemical energy into electrical energy.

Cited by 17 publications

References 39 publications

Facile Synthesis of Fiber‐Reinforced Catalyst for High Performance Ethanol and 2‐Propanol Oxidation

Facile Synthesis of Fiber‐Reinforced Catalyst for High Performance Ethanol and 2‐Propanol Oxidation

Catalyst Development for High‐Temperature Polymer Electrolyte Membrane Fuel Cell (HT‐PEMFC) Applications

Nitrogen-doped graphene quantum dots as a support for Ni–Au nanoparticles: efficient electrocatalysts for ethanol and formate fuel cells using hydrogen peroxide as an oxidant

Contact Info

Product

Resources

About