Sustainable design and life cycle engineering of adhesive joints for polymeric products: assessment of surface activation technologies

A conformal cooling channel (CCC) follows the mold core or cavity profile to carry out uniform cooling in the cooling stage. However, the significant pressure drop along the cooling channels is a distinct disadvantage of the CCC. In this study, an innovative waterfall cooling channel (WCC) was proposed and implemented. The WCC cools the injected products via surface contact, replacing the conventional line contact to cool the injected products. The WCC was optimized using numerical simulation software. Silicone rubber molds with two kinds of cooling channels were designed and implemented. The cooling time of the molded part was evaluated using a low-pressure wax injection molding machine. The experimental results of the cooling time of the molded part were compared with the simulation results from numerical simulation software. The results showed that the optimal mesh element count was about 1,550,000 with a mesh size of 1 mm. The simulation software predicted the filling time of the water cup injection-molded product to be approximately 2.008 s. The cooling efficiency for a silicone rubber mold with a WCC is better than that of the silicone rubber mold with a CCC since the core and cavity cooling efficiency is close to 50%. The pressure drop of the WCC is smaller than that of the CCC, which reduces the pressure drop by about 56%. Taking a water cup with a mouth diameter of 70 mm, a height of 60 mm, and a thickness of 2 mm as an example, the experimental results confirmed that the use of the WCC can save the cooling time of the product by about 265 s compared with the CCC. This shows how a WCC can increase cooling efficiency by approximately 17.47%.

Section: Introductionmentioning

confidence: 99%

Development of a Silicone Rubber Mold with an Innovative Waterfall Cooling Channel

Kuo,

Lin,

et al. 2024

“…In recent years, the adoption of conformal cooling channels (CCs) [1] in injection molds or dies has emerged as a widely recommended standard for enhancing mold capabilities. CC denotes a specialized type of cooling system tailored for dies or molds employed in diverse manufacturing processes, including blow molding [2], metal forming [3], plastic injection molding [4], die casting [5], and metal injection molding. The distinctive characteristic of CC lies in its capacity to enhance heat dissipation during the cooling phase across various manufacturing operations.…”

Section: Introductionmentioning

confidence: 99%

Enhancing the Cooling Efficiency of Aluminum-Filled Epoxy Resin Rapid Tool by Changing Inner Surface Roughness of Cooling Channels

Kuo,

Chen,

Lin

et al. 2024

In low-pressure wax injection molding, cooling time refers to the period during which the molten plastic inside the mold solidifies and cools down to a temperature where it can be safely ejected without deformation. However, cooling efficiency for the mass production of injection-molded wax patterns is crucial. This work aims to investigate the impact of varying surface roughness on the inner walls of the cooling channel on the cooling efficiency of an aluminum-filled epoxy resin rapid tool. It was found that the cooling time for the injection-molded products can be determined by the surface roughness according to the proposed prediction equation. Employing fiber laser processing on high-speed steel rods allows for the creation of microstructures with different surface roughness levels. Results demonstrate a clear link between the surface roughness of cooling channel walls and cooling time for molded wax patterns. Employing an aluminum-filled epoxy resin rapid tool with a surface roughness of 4.9 µm for low-pressure wax injection molding can save time, with a cooling efficiency improvement of approximately 34%. Utilizing an aluminum-filled epoxy resin rapid tool with a surface roughness of 4.9 µm on the inner walls of the cooling channel can save the cooling time by up to approximately 60%. These findings underscore the significant role of cooling channel surface roughness in optimizing injection molding processes for enhanced efficiency.

A Cost-Effective Approach to Creating Large Silicone Rubber Molds Using Advanced Rigid Polyurethane Foam

Kuo,

Lu,

Huang

et al. 2024

In practical applications, polyurethane (PU) foam must be rigid to meet the demands of various industries and provide comfort and protection in everyday life. PU foam components are extensively used in structural foam, thermal insulation, decorative panels, packaging, imitation wood, and floral foam, as well as in models and prototypes. Conventional technology for producing PU foam parts often leads to defects such as deformation, short shots, entrapped air, warpage, flash, micro-bubbles, weld lines, and voids. Therefore, the development of rigid PU foam parts has become a crucial research focus in the industry. This study proposes an innovative manufacturing process for producing rigid PU foam parts using silicone rubber molds (SRMs). The deformation of the silicone rubber mold can be predicted based on its wall thickness, following a trend equation with a correlation coefficient of 0.9951. The volume of the PU foam part can also be predicted by the weight of the PU foaming agent, as indicated by a trend equation with a correlation coefficient of 0.9824. The optimal weight ratio of the foaming agent to water, yielding the highest surface hardness, was found to be 5:1. The surface hardness of the PU foam part can also be predicted based on the weight of the water used, according to a proposed prediction equation with a correlation coefficient of 0.7517. The average surface hardness of the fabricated PU foam part has a Shore O hardness value of approximately 75. Foam parts made with 1.5 g of water added to 15 g of a foaming agent have the fewest internal pores, resulting in the densest interior. PU foam parts exhibit excellent mechanical properties when 3 g of water is added to the PU foaming agent, as evidenced by their surface hardness and compressive strength. Using rigid PU foam parts as a backing material in the proposed method can reduce rapid tool production costs by about 62%. Finally, an innovative manufacturing process for creating large SRMs using rigid PU foam parts as backing material is demonstrated.