Surface Pretreatment and Fabrication Technology of Braided Carbon Fiber Rope Aluminum Matrix Composite

Liang, Jun; Wu, Chensheng; Ping, Hang; Wang, Ming; Tang, Wenbo

doi:10.3390/met10091212

Cited by 5 publications

(3 citation statements)

References 38 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In that C1s and O1s peaks are majorly because of two possibilities; they are either dissociated in the vicinity of the surface, by a charge transfer into the oxygen antibonding molecular orbital or otherwise the whole oxygen molecule is reflected from the surface carbonization and oxidation. Its respective binding energy obtained was 284.82 eV and 532.93 eV (Liang et al , 2020; Jalar et al , 2014). The major aluminium peaks are attained at the binding energy of 74.4 ± 0.1 eV and the minor change in binding energy is may be because of the reinforcement effect of ZnO with the matrix alloy (Yang et al , 2016).…”

Section: Resultsmentioning

confidence: 97%

A study on tribological behaviour and analysis of ZnO reinforced AA6061 matrix composites fabricated by stir casting route

Ramanathan

Bhuvaneswari

et al. 2021

ILT

View full text Add to dashboard Cite

Purpose The most promising replacements for the industrial applications are particle reinforced metal matrix composites because of their good and combined mechanical properties. Currently, the need of matrix materials for industrial applications is widely satisfied by aluminium alloys. The purpose of this paper is to evaluate the tribological behaviour of the zinc oxide (ZnO) particles reinforced AA6061 composites prepared by stir casting route. Design/methodology/approach In this study, AA6061 aluminium alloy matrix reinforced with varying weight percentages (3%, 4.5% and 6%) of ZnO particles, including monolithic AA6061 alloy samples, is cast by the most economical fabrication method, called stir casting. The prepared sample was subjected to X-ray photoelectron spectroscopy (XPS) analysis, experimental density measurement by Archimedian principle and theoretical density by rule of mixture and hardness test to investigate mechanical property. The dry sliding wear behaviour of the composites was investigated using pin-on-disc tribometer with various applied loads of 15 and 20 N, with constant sliding velocity and distance. The wear rate, coefficient of friction (COF) and worn surfaces of the composite specimens and their effects were also investigated in this work. Findings XPS results confirm the homogeneous distribution of ZnO microparticles in the Al matrix. The Vickers hardness result reveals that higher ZnO reinforced (6%) sample have 34.4% higher values of HV than the monolithic aluminium sample. The sliding wear tests similarly show that increasing the weight percentage of ZnO particles leads to a reduced wear rate and COF of 30.01% and 26.32% lower than unreinforced alloy for 15 N and 36.35% and 25% for 20 N applied load. From the worn surface morphological studies, it was evidently noticed that ZnO particles dispersed throughout the matrix and it had strong bonding between the reinforcement and the matrix, which significantly reduced the plastic deformation of the surfaces. Originality/value The uniqueness of this work is to use the reinforcement of ZnO particles with AA6061 matrix and preparing by stir casting route and to study and analyse the physical, hardness and tribological behaviour of the composite materials.

show abstract

Section: Resultsmentioning

confidence: 97%

A study on tribological behaviour and analysis of ZnO reinforced AA6061 matrix composites fabricated by stir casting route

Ramanathan

Bhuvaneswari

et al. 2021

ILT

View full text Add to dashboard Cite

show abstract

“…The surface of the carbon fiber braided rope treated with ultrasonic degumming contains many hydrophilic oxygen-containing functional groups, which can effectively improve the wettability between the carbon fiber braided rope and the aluminum matrix. Additionally, a copper coating can effectively inhibit the formation of Al4C3 brittle phase [10].…”

Section: Contributionsmentioning

confidence: 99%

Surface Engineering of Metals and Alloys

Rokosz

2022

Metals

View full text Add to dashboard Cite

show abstract

“…When carbon fibers are shipped from the factory, the surface is usually coated with organic epoxy protective adhesive in order to protect the clean and active fiber surface from adsorbing moisture and dust in the air [18,19]. In this experiment, PAN-based (T700) carbon fiber produced by Toray, Japan was used, and its main performance parameters are shown in Table 1.…”

Section: Removal Of Surface Sizing Materials From Carbon Fibersmentioning

confidence: 99%

Forming Process and Simulation Analysis of Helical Carbon Fiber Reinforced Aluminum Matrix Composite

Liang

Zhao

et al. 2021

Metals

Self Cite

View full text Add to dashboard Cite

In order to promote the industrialization of the large deformation technology of carbon fiber composites, this paper studies a new method of forming of helical carbon fiber reinforced aluminum matrix composite. The purpose is to solve the problem of large deformation of carbon fiber with low elongation and metal matrix with high elongation. By introducing carbon fiber with helical space structure into the aluminum matrix, the helical carbon fiber reinforced aluminum matrix composites were prepared and the subsequent drawing deformation was carried out. Here we systematically studied the large plastic deformation behavior of helical carbon fiber reinforced aluminum matrix composite via a combination of numerical simulations and experiments, and analyzed the deformation law and stress of helical carbon fiber in the deformation process. We found that the plastic deformation of the composite causes local stress concentration around the helical carbon fiber, and the helical carbon fiber will move synchronously with the aluminum matrix during the deformation, and receive the pressure from the aluminum matrix. Second, the best process parameters obtained from the simulation, that is, the drawing die angle α = 7°, when five-pass drawing experiments were carried out, the total deformation reached 58%, and the average elongation of a single pass was 18.9%. The experimental show carbon fiber reinforced aluminum matrix composite with helical space structure can achieve large deformation and high strength. The experimental and simulation are in general agreement, which verifies the correctness of the carbon fiber helical structure model.

show abstract

Surface Pretreatment and Fabrication Technology of Braided Carbon Fiber Rope Aluminum Matrix Composite

Cited by 5 publications

References 38 publications

A study on tribological behaviour and analysis of ZnO reinforced AA6061 matrix composites fabricated by stir casting route

A study on tribological behaviour and analysis of ZnO reinforced AA6061 matrix composites fabricated by stir casting route

Surface Engineering of Metals and Alloys

Forming Process and Simulation Analysis of Helical Carbon Fiber Reinforced Aluminum Matrix Composite

Contact Info

Product

Resources

About