Surface Acoustic Wave (SAW)-Impedance Sensor for Kinetic Assay of Trypsin

Cai, Qingyun; Wang, Ronghui; Wu, Longmei; Yao, Shouzhuo

doi:10.1006/mchj.1996.1320

Cited by 5 publications

(1 citation statement)

References 10 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Otherwise, it may add to the cost of sensor preparation and affect the consistency in mass production. In last few years, a different kind of SAW impedance sensor had been developed and used in humidity measurements or other applications [13][14][15]. As we know that chemically, thermally, and mechanically γ-Al 2 O 3 is a highly stable material, this nanoporous metal oxide will be suitable for humidity measurement.…”

Section: Introductionmentioning

confidence: 99%

A nanoporous thin-film miniature interdigitated capacitive impedance sensor for measuring humidity

Islam

Mittal

Nimal

et al. 2014

International Journal of Smart and Nano Materials

View full text Add to dashboard Cite

This paper presents a development of a low-cost miniature humidity sensor with an interdigitated aluminium electrode connected in parallel on quartz substrate. Interdigitated capacitive device has been fabricated using the photolithography method. The aluminium electrode was covered with sensitive film of a nanoporous thin film of γ-Al 2 O 3 made from novel sol-gel technique. Nanostructured thin film offers very high surface to volume ratio with distribution of micro pores for moisture detection. Pore morphologies of the film have been studied by field emission electron microscope and Xray diffraction methods. Impedance measurement of the miniature capacitive humidity sensor toward relative humidity was investigated at room temperature by Agilent 4294A impedance analyzer (Agilent, Santa Clara, CA, USA). The device exhibits short response and recovery times and good repeatability.

show abstract

Section: Introductionmentioning

confidence: 99%

A nanoporous thin-film miniature interdigitated capacitive impedance sensor for measuring humidity

Islam

Mittal

Nimal

et al. 2014

International Journal of Smart and Nano Materials

View full text Add to dashboard Cite

show abstract

Instrumentation for Kinetics

Cordos

2000

Encyclopedia of Analytical Chemistry

View full text Add to dashboard Cite

In kinetic methods or reaction‐rate methods of analysis, the rate of a given reaction is measured and related to the concentration of the sought‐for species. The instrumentation in kinetics is primarily designed to monitor the evolution of the analytical signal with time. Unlike in the traditional equilibrium‐based approaches, where the signal is measured after the reaction has reached completion, in kinetic methods the signal is usually measured in the first few percent of the total reaction time. Therefore, the advantages and limitations of kinetic methods should be considered in their relations with equilibrium methods. Kinetic methods are faster than equilibrium‐based methods since the user does not have to wait for a reaction to go to completion. They are relative methods that depend on changes in concentration and not on its absolute value and they could be more selective than equilibrium methods since the difference between reaction constants could be used to discriminate against an interfering species. The limitations of kinetic methods are a lower precision and a strong dependence on experimental conditions. The main factors that cause these limitations are the measured signal, which is small in comparison with that from an equilibrium reaction, and the dependence of rate constants on temperature, pH, ionic strength, etc. Therefore, the measurement systems used in kinetic methods should be sensitive and the experimental conditions should be kept strictly constant. The best results in kinetic methods are obtained with instrumental systems having a high degree of automation. The main operations that should be carried out by the instrumentation in kinetic determinations are the mixing of the reactants, measurement of the detector signal in time and processing of data to obtain the reaction rate and concentration. The mixing of the reactants should be done in a time shorter than the reaction half‐life and it is critical for fast reactions where required mixing times are of the order of milliseconds. In these cases the mixing is accomplished by mechanical systems that rapidly drive the reactants through a mixing chamber into an observation chamber. For slower reaction the best mixing procedures are based on automated flow analyzers that have different manifolds configurations adapted both to sample processing and to reactant mixing. After mixing, the reaction could be monitored in time either by stopping the flow and recording the signal or by passing the reacting plug several times through the detector and reading the signal after each pass. The measurement of the detector signal, after the reagents are mixed, could be done with a large variety of detectors, but the most commonly used detection systems are photometric and electrochemical. Photometric detection provides a short response time, specificity and the possibility of collecting full spectra very rapidly if photodetector arrays are used. Electrochemical detectors are simple and relatively inexpensive. The concentration of the analyte is determined from the slope of the detector signal. In many routine procedures the slope is determined by measuring the signal at one or two fixed points in time or by determining the time required by the signal to reach a predetermined level. These procedures have the advantage that they are rapid and need no supplementary instrumentation for data processing. Another approach in kinetic data processing, based on computer software, computes a curve that fits the experimental data. The slope or concentration is then extracted from the mathematical expression of the fitting curve.

show abstract

A novel surface acoustic wave-impedance humidity sensor based on the composite of polyaniline and poly(vinyl alcohol) with a capability of detecting low humidity

Deng

Yang

2012

Sensors and Actuators B: Chemical

View full text Add to dashboard Cite

Surface Acoustic Wave (SAW)-Impedance Sensor for Kinetic Assay of Trypsin

Cited by 5 publications

References 10 publications

A nanoporous thin-film miniature interdigitated capacitive impedance sensor for measuring humidity

A nanoporous thin-film miniature interdigitated capacitive impedance sensor for measuring humidity

Instrumentation for Kinetics

A novel surface acoustic wave-impedance humidity sensor based on the composite of polyaniline and poly(vinyl alcohol) with a capability of detecting low humidity

Contact Info

Product

Resources

About