Study on plastic behaviours of CuNi10Fe1Mn alloy tubes under cast-roll process

Fu, Yabo; Yan, Zhiming; Li, Tingju; Cheng, Yanfeng; Yin, Guomao

doi:10.1016/j.matdes.2009.06.003

Cited by 12 publications

(2 citation statements)

References 4 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Cu–10wt–%Ni–1wt-%Fe alloy (nickel bronze) is widely used in various industries such as manufacturing of high-strength tubes for heat exchangers in shipbuilding, ferrules, saltwater piping and so on, due to its excellent corrosion resistance and good mechanical properties [2,5,6]. It is considered that Cu–10wt-%Ni–1wt-%Fe clad steel composite strip has excellent corrosion resistance and comprehensive mechanical properties of steel, which possesses both advantages of the two materials.…”

Section: Introductionmentioning

confidence: 99%

Characterisation of steel/nickel bronze clad strips prepared by continuous solid/liquid bonding method

Jie

Liu

Wang

et al. 2019

Materials Science and Technology

Self Cite

View full text Add to dashboard Cite

A continuous solid/liquid bonding method was successfully developed to fabricate Cu–10wt-%Ni–1wt-%Fe (nickel bronze) clad steel with a good metallurgical bonding in the present study. The results indicated that the diffusion distance of interface is about 1.90–2.18 µm. The average tensile shear strength of centre composite strip at as-cast state is 228 ± 5 MPa, while that of edge is 202 ± 6 MPa, and the interface strength is higher than that of bronze since the fracture always occurs on the nickel bronze side. After the rolling process, the tensile shear strength increases with the increasing rolling reduction. The reason can be ascribed to the strengthening of the nickel bronze whose strength is still lower than the interface.

show abstract

Section: Introductionmentioning

confidence: 99%

Characterisation of steel/nickel bronze clad strips prepared by continuous solid/liquid bonding method

Jie

Liu

Wang

et al. 2019

Materials Science and Technology

Self Cite

View full text Add to dashboard Cite

show abstract

“…The CuNi10Fe1Mn alloy is a kind of white copper that mainly contains elements Cu and Ni, which can be used for condenser pipe in thermal power, nuclear power, warships and sea water desalinization can be produced by the horizontal continuous casting method [1]. In the practical application, the CuNi10Fe1Mn alloy must has not only higher heat transfer efficiency and better mechanical features, but also good corrosion resistance.…”

Section: Introductionmentioning

confidence: 99%

Effect of Rotating Electromagnetic Field on Corrosion Behavior of CuNi<sub>10</sub>Fe<sub>1</sub>Mn Alloy Tube Billet

Huang

2012

AMM

View full text Add to dashboard Cite

The effects of the rotating electromagnetic field (REF) on the corrosion behavior of the CuNi10Fe1Mn alloy tube billets were investigated by immersion test and electrochemical measurements. It is found that the imposing REF can be used to improve the resulting microstructures which affect the corrosion behavior of the CuNi10Fe1Mn alloy tube billet. The REF could induce the microstructure changes of the CuNi10Fe1Mn alloy tube billets and result in the gains refinement and the preferred orientation on the crystal plane. The improvement of the corrosion behavior is contributed to the change of microstructures of BFe10-1-1 alloy tube billets. The electrochemical measurements and immersion test show that the CuNi10Fe1Mn alloy tube billets with REF increase the corrosion resistance compared with the CuNi10Fe1Mn alloy tube billets without REF. Therefore all these observations suggested a nobler corrosion behavior of the CuNi10Fe1Mn alloy tube billets with the REF.

show abstract

Influence of Hot Rolling and Solution Treatment on the Microstructure and Mechanical Properties of High-Boron Duplex Stainless Steel 0Cr21Ni5Ti-2B

Wang

2021

Met Sci Heat Treat

View full text Add to dashboard Cite

Study on plastic behaviours of CuNi10Fe1Mn alloy tubes under cast-roll process

Cited by 12 publications

References 4 publications

Characterisation of steel/nickel bronze clad strips prepared by continuous solid/liquid bonding method

Characterisation of steel/nickel bronze clad strips prepared by continuous solid/liquid bonding method

Effect of Rotating Electromagnetic Field on Corrosion Behavior of CuNi<sub>10</sub>Fe<sub>1</sub>Mn Alloy Tube Billet

Influence of Hot Rolling and Solution Treatment on the Microstructure and Mechanical Properties of High-Boron Duplex Stainless Steel 0Cr21Ni5Ti-2B

Contact Info

Product

Resources

About