Sliding Wear Behaviour and Corosion Resistance to Ringer’s Solution of Uncoated and DLC Coated X46Cr13 Steel

Scendo, M.; Radek, Norbert; Konstanty, Janusz; Staszewska, Katarzyna

doi:10.1515/amm-2016-0305

Cited by 3 publications

(2 citation statements)

References 23 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…But, this metal has a limited corrosion resistance and therefore the corrosion of carbon steels is a problem for most industries [1,2]. Therefore, many efforts have been done to increase corrosion resistance and stability of steel materials [3,4]. There are different corrosion protection methods including cathodic/anodic protection, coatings, inhibitors and proper design [5][6][7][8].…”

Section: Introductionmentioning

confidence: 99%

Archives of Metallurgy and Materials

Majdi¹,

Danaee²,

Zaarei³

et al. 2020

View full text Add to dashboard Cite

Silicate coatings have been considered as an alternative to toxic and carcinogenic other chemical treatments. In this paper, a strengthened silicate coating was formed on the surface of low carbon steel by dip immersion method. The modification and strengthening was done by loading colloidal nano-SiO 2 into the film. The characterizations of nano-SiO 2 were investigated by FESEM, TEM and FT-IR. The effects of nano contents (weight ratio) and drying temperatures on corrosion properties of silicate film were studied. Potentiodynamic polarization, electrochemical impedance spectroscopy and immersion tests have been used to study corrosion behavior of nano-loaded silicate films. Surface morphology, microstructure and its chemical composition were analyzed by means of FESEM, EDS, AFM, XRD, GIXRD, ATR-FTIR and Raman techniques. Results indicated that colloidal nano-SiO 2 properly modified the silicate coatings and significantly improved the corrosion resistance and barrier property. Also drying temperature showed a considerable effect in silicate coating and higher corrosion resistance was obtained with 150°C curing.

show abstract

Section: Introductionmentioning

confidence: 99%

Archives of Metallurgy and Materials

Majdi¹,

Danaee²,

Zaarei³

et al. 2020

View full text Add to dashboard Cite

show abstract

“…A brief research work of the influence of process parameters on the quality of thermally sprayed material coating is given in [ 10 ] since the final coating quality is strongly related to the spray parameters’ definition, such as oxygen pressure, fuel gas type, etc. Sliding wear properties and corrosion resistance related to X46Cr13 steel were tested, and this problem is treated in [ 11 ]. Mechanical data on this steel are very scarce in the literature.…”

Section: Introductionmentioning

confidence: 99%

Analysis of the Mechanical Behavior, Creep Resistance and Uniaxial Fatigue Strength of Martensitic Steel X46Cr13

et al. 2017

View full text Add to dashboard Cite

The article deals with the analysis of the mechanical behavior at different temperatures, uniaxial creep and uniaxial fatigue of martensitic steel X46Cr13 (1.4034, AISI 420). For the purpose of considering the aforementioned mechanical behavior, as well as determining the appropriate resistance to creep and fatigue strength levels, numerous uniaxial tests were carried out. Tests related to mechanical properties performed at different temperatures are presented in the form of engineering stress-strain diagrams. Short-time creep tests performed at different temperatures and different stress levels are presented in the form of creep curves. Fatigue tests carried out at stress ratios R=0.25 and R=−1 are shown in the form of S–N (fatigue) diagrams. The finite fatigue regime for each of the mentioned stress ratios is modeled by an inclined log line, while the infinite fatigue regime is modeled by a horizontal line, which represents the fatigue limit of the material and previously was calculated by the modified staircase method. Finally, the fracture toughness has been calculated based on the Charpy V-notch impact energy.

show abstract

Assessment of the Inhibition Efficiency of 3-amino-5-methylthio-1H-1,2,4-triazole Against the Corrosion of Mild Steel in Acid Chloride Solution

Scendo¹

2017

International Journal of Electrochemical Science

View full text Add to dashboard Cite

Influence of 3-amino-5-methylthio-1H-1,2,4-triazole (AMTTA) concentration on the corrosion of C45 mild steel in acid chloride solutions were studied. The potentiodynamic (PD) polarization, electrochemical impedance spectroscopy (EIS) methods and quantum chemical calculations were used. The surface morphology of specimens were observed through inverted metallographic microscope (IMM). It has been shown that the inhibition efficiency increased with an increase in the concentration of 3-amino-5-methylthio-1H-1,2,4-triazole. Tafel polarization study revealed that AMTTA acted as mixed type inhibitor. The best fit to the experimental data was obtained using Temkin adsorption isotherm. It was found that the adsorption of inhibitor on the mild steel surface takes place through a typical physisorption. Moreover, the adsorption mechanism of AMTTA on C45 mild steel surface was proposed and discussed.

show abstract

Sliding Wear Behaviour and Corosion Resistance to Ringer’s Solution of Uncoated and DLC Coated X46Cr13 Steel

Cited by 3 publications

References 23 publications

Archives of Metallurgy and Materials

Archives of Metallurgy and Materials

Analysis of the Mechanical Behavior, Creep Resistance and Uniaxial Fatigue Strength of Martensitic Steel X46Cr13

Assessment of the Inhibition Efficiency of 3-amino-5-methylthio-1H-1,2,4-triazole Against the Corrosion of Mild Steel in Acid Chloride Solution

Contact Info

Product

Resources

About