Room temperature creep behavior of Ti–Nb–Ta–Zr–O alloy

Zhang, Weidong; Liu, Yong; Wu, Hong; Lan, Xiaodong; Qiu, Jingwen; Hu, Te; Tang, Huiping

doi:10.1016/j.matchar.2016.05.001

Cited by 27 publications

(10 citation statements)

References 31 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In a similar study, the stress exponent was found to be in the range of 20-60 for IN-718 at room temperature and decreased to 8-18 at 923 K [32]. The magnitude of stress exponent depends on the balance between generation and annihilation of dislocations [33]. Larger value of stress exponent is typically obtained when more dislocations are generated and involved during deformation [33].…”

Section: Discussionmentioning

confidence: 86%

“…The magnitude of stress exponent depends on the balance between generation and annihilation of dislocations [33]. Larger value of stress exponent is typically obtained when more dislocations are generated and involved during deformation [33]. The decrease in n value with increasing temperature may be due to enhancement in dislocation diffusivity and thermal recovery at higher temperature, so annihilation competes with dislocation generation.…”

Section: Discussionmentioning

confidence: 99%

See 1 more Smart Citation

High-Temperature Nano-Indentation Creep Behavior of Multi-Principal Element Alloys under Static and Dynamic Loads

Sadeghilaridjani

Mukherjee

2020

Metals

View full text Add to dashboard Cite

Creep is a serious concern reducing the efficiency and service life of components in various structural applications. Multi-principal element alloys are attractive as a new generation of structural materials due to their desirable elevated temperature mechanical properties. Here, time-dependent plastic deformation behavior of two multi-principal element alloys, CoCrNi and CoCrFeMnNi, was investigated using nano-indentation technique over the temperature range of 298 K to 573 K under static and dynamic loads with applied load up to 1000 mN. The stress exponent was determined to be in the range of 15 to 135 indicating dislocation creep as the dominant mechanism. The activation volume was ~25b3 for both CoCrNi and CoCrFeMnNi alloys, which is in the range indicating dislocation glide. The stress exponent increased with increasing indentation depth due to higher density and entanglement of dislocations, and decreased with increasing temperature owing to thermally activated dislocations. The results for the two multi-principal element alloys were compared with pure Ni. CoCrNi showed the smallest creep displacement and the highest activation energy among the three systems studied indicating its superior creep resistance.

show abstract

Section: Discussionmentioning

confidence: 86%

Section: Discussionmentioning

confidence: 99%

High-Temperature Nano-Indentation Creep Behavior of Multi-Principal Element Alloys under Static and Dynamic Loads

Sadeghilaridjani

Mukherjee

2020

Metals

View full text Add to dashboard Cite

show abstract

“…The stress exponent of HEAs at 1 N decreased significantly from 130-140 to 30-50 with an increase in temperature due to thermally activated dislocations at elevated temperature; however, the degree of reduction was not sharp in the case of pure W (from~50 to~30). The magnitude of stress exponent depends on the density of dislocations involved during deformation and whether the deformation is dominated by generation or annihilation of dislocations [36]. The decrease of n value with increasing temperature is due to the enhancement of dislocation movement and more thermal recovery at a higher temperature compared to their generation [17].…”

Section: Discussionmentioning

confidence: 99%

High-Temperature Nano-Indentation Creep of Reduced Activity High Entropy Alloys Based on 4-5-6 Elemental Palette

Sadeghilaridjani

Muskeri

Pole

et al. 2020

Entropy

View full text Add to dashboard Cite

There is a strong demand for materials with inherently high creep resistance in the harsh environment of next-generation nuclear reactors. High entropy alloys have drawn intense attention in this regard due to their excellent elevated temperature properties and irradiation resistance. Here, the time-dependent plastic deformation behavior of two refractory high entropy alloys was investigated, namely HfTaTiVZr and TaTiVWZr. These alloys are based on reduced activity metals from the 4-5-6 elemental palette that would allow easy post-service recycling after use in nuclear reactors. The creep behavior was investigated using nano-indentation over the temperature range of 298 K to 573 K under static and dynamic loads up to 5 N. Creep stress exponent for HfTaTiVZr and TaTiVWZr was found to be in the range of 20–140 and the activation volume was ~16–20b3, indicating dislocation dominated mechanism. The stress exponent increased with increasing indentation depth due to a higher density of dislocations and their entanglement at larger depth and the exponent decreased with increasing temperature due to thermally activated dislocations. Smaller creep displacement and higher activation energy for the two high entropy alloys indicate superior creep resistance compared to refractory pure metals like tungsten.

show abstract

“…Creep reflects the time effect on mechanical properties of materials. Over the past few years, many scholars have conducted in-depth studies on the creep behavior of metal materials at room D r a f t temperature (Zhao et al 2008;Zhang et al 2016;Gong et al 2017). Liu et al (2001) studied the creep behavior of high strength steels at room temperature.…”

Section: Introductionmentioning

confidence: 99%

Study on creep performance of launch canister under long-term storage

Sun

Xiao³

2019

Transactions of the Canadian Society for Mechanical Engineering

View full text Add to dashboard Cite

In this paper, the creep performance of a multi-barrel rocket launch canister under long-term stacking storage is studied. Based on the Bailey–Norton model, a creep model for the frame material of a launch canister was established. Constant stress tensile creep tests under different stress levels at room temperature were carried out on the frame materials of the launch canister and the creep model parameters were obtained by test data fitting. The three-dimensional finite element model of the launch canister was established in the ABAQUS software environment and the creep deformation of the launch canister after long-term stacking storage was studied. The results indicated that the bottom layer of the launch canister frame presented an extended residual deformation when the stacking storage solution with the original support pad was used. Therefore, a position adjustment program of the support pad was put forward. The residual deformation of the launch canister frame after long-term storage could be significantly reduced, thus the performance requirements for the launch canister are guaranteed.

show abstract

Room temperature creep behavior of Ti–Nb–Ta–Zr–O alloy

Cited by 27 publications

References 31 publications

High-Temperature Nano-Indentation Creep Behavior of Multi-Principal Element Alloys under Static and Dynamic Loads

High-Temperature Nano-Indentation Creep Behavior of Multi-Principal Element Alloys under Static and Dynamic Loads

High-Temperature Nano-Indentation Creep of Reduced Activity High Entropy Alloys Based on 4-5-6 Elemental Palette

Study on creep performance of launch canister under long-term storage

Contact Info

Product

Resources

About