Research on MTPA control of IPMSM Drive Using Online Parameter Identification Method

Zhang, Nan; Yin, Dejun

doi:10.1109/acpee48638.2020.9136376

Cited by 4 publications

(4 citation statements)

References 12 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Therefore, the voltage limit curve decides the minimum current required to produce the desired torque. The copper loss is also reduced in the FW region (2,3) . These limit values are given by equations ( 21) and ( 22) respectively.…”

Section: Field Weakening (Fw) Controlmentioning

confidence: 99%

“…A lot of research has been done on PM material, power electronics devices, and control topologies, so we can develop an efficient IPMSM motor that offers accurate speed control over a wide range of speeds, high efficiency, is compact, has low copper losses, has a long bearing grease life, and has a highpower density. So IPMSM is most suitable for loads like electric vehicles, elevators, and traction, in which space limitations are important (1)(2)(3)(4) .…”

Section: Introductionmentioning

confidence: 99%

“…We control the speed from zero to the base (rated) speed by MTPA and beyond the base speed by the FW methodology. (2,3) IPMSM has permanent magnets buried inside the rotor structure. Its rotor surface will become smooth, and the air gap will be reduced.…”

Section: Introductionmentioning

confidence: 99%

“…It will give us an extra torque produced by the daxis current called "reluctance torque. " (5) Therefore, in MTPA, we get maximum torque per unit current; this is how we can reduce the copper loss in IPMSM to its minimum and get better efficiency (3,4) . We will reduce the flux by negative d-axis current to go beyond the base speed of operation.…”

Section: Introductionmentioning

confidence: 99%

See 3 more Smart Citations

High-Performance and Robust Field-Oriented Control of IPMSM Drive Over Wide Speed Operation by PI and Fuzzy Intelligent Controllers

Baria,

Patel,

Dalwadi

et al. 2023

IJST

View full text Add to dashboard Cite

Objectives: This paper simulates a high-performance PI and FLC-based controller for an IPMSM drive in which the speed should closely follow the reference speed and voltage-current trajectory with different conditions like load disturbance, variation in circuit parameters, and control strategy. In FOC, the PI and fuzzy controller are used for sliding mode control. This controller generates the d-axis current (Id) and q-axis current (Iq), which control the torque and magnetic field vector for each stator winding, so the speed of the motor can be effectively controlled. Methods: In this paper, we used two loops: one is the outer speed loop, and another is the inner loop called the current loop, which generates the pulses for the inverter. The optimal behavior of the controllers is designed based on the Maximum Torque per Ampere (MTPA) method for stand-still to base speed operation and the Field Weakening (FW) method for the above base speed operation. The mathematical model of the IPMSM motor can be derived from its dynamic d-q model. This proposed drive system is simulated in MATLAB-Simulink software with different conditions like speeds and loads. Moreover, the fixed-gain PI controller is mostly affected by the step change in reference speed, circuit parameters, and load condition. The accurate speed control of the drive becomes a complex issue due to the non-linear coupling between the stator current and rotor and the nonlinearity in the torque. Therefore, the fuzzy controller is more popular in highperformance IPMSM drives. Novelty: In this paper, the FLC is used as a speed controller, and the proposed control scheme reduces the computation for real-time implementation. The hysteresis current controllers are used, and outputs are given to logic, which is used to switch ON and OFF the inverter. The robustness of the FLC-based drive is verified by theoretical and simulation results. In this paper, the three inputs to the FLC are: is the change in rotor speed, ω r is rotor speed, and ∆e is the change in speed error. Fuzzy rules are developed by different membership functions used to obtain the optimized value (I d * and Iq*), which gives precise speed control under different operating https://www.indjst.org/ conditions over a wide speed range.

show abstract

Section: Field Weakening (Fw) Controlmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

See 2 more Smart Citations