Remarkably improved interfacial adhesion of UHMWPE fibers reinforced composite by constructing a three-dimensional stacked nanoparticles structure at interphase

Wang, Kui; Shen, Lu; Lü, Rong; Zhao, Yao; Qin, Zongbao

doi:10.1016/j.jiec.2022.03.031

Cited by 9 publications

(2 citation statements)

References 40 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…43 In general, the wettability between fiber and polymer matrix is positively correlated with the surface energy of fiber. 44 Surface energy can be calculated based on Owens-Wendt surface energy component method, 45 which has been shown in Equations ( 2)-( 4).…”

Section: Wettability Between Uhmwpe Fiber and Rubbermentioning

confidence: 99%

Study on catechol/tetraethylenepentamine and nano zinc oxide co‐modifying ultrahigh molecular weight polyethylene fiber surface to improve interfacial adhesion

Fang

Chen

et al. 2022

Polymers for Advanced Techs

View full text Add to dashboard Cite

To improve interfacial adhesion to rubber matrix, a lower cost surface modification strategy of ultrahigh molecular weight polyethylene (UHMWPE) fiber was proposed by replacing expensive dopamine with the two‐component system of catechol/tetraethylenepentamine (CAT/TEPA) and then depositing nano zinc oxide (ZnO NPs). By Michael addition reaction or Schiff base reaction between CAT and TEPA, the CAT/TEPA layer was coated on the fiber surface, and further served as a secondary functional platform to realize ZnO NPs deposition through coordination. The surface morphology, chemical structure and composition, wettability and thermal property of the UHMWPE fibers were investigated to evaluate the process and effect of the surface modification. The results of the single‐filament tensile test indicated that the tensile strength of the UHMWPE fibers has no deterioration after the modification treatment. In comparison with the original fiber, the pull‐out test showed that the highest interface adhesion between the modified UHMWPE fibers and rubber matrix increased by 80.4%. Additionally, it was found that the appropriate zinc ion concentration played an important role in the modification effect.

show abstract

Section: Wettability Between Uhmwpe Fiber and Rubbermentioning

confidence: 99%

Study on catechol/tetraethylenepentamine and nano zinc oxide co‐modifying ultrahigh molecular weight polyethylene fiber surface to improve interfacial adhesion

Fang

Chen

et al. 2022

Polymers for Advanced Techs

View full text Add to dashboard Cite

show abstract

“…UHMWPE fiber-reinforced composite laminates with orthogonal unidirectional (UD) structure have no interweaving between the layers of fibers, low matrix content, and the existence of gaps inside the material. The interlaminar shear strength is very low compared to the tensile strength [21][22][23], which leads to the tendency of delamination slippage in tensile property tests of UHMWPE laminates and affect the reliability of test results. In this regard, numerous scholars have carried out a lot of fruitful work on the tensile property tests of UHMWPE fiber-reinforced composites by improving the test methods.…”

Section: Introductionmentioning

confidence: 99%

Temperature and Strain Rate Related Deformation Behavior of UHMWPE Fiber-Reinforced Composites

Yi,

Xu,

Tian

et al. 2024

Polymers

View full text Add to dashboard Cite

As they possess the qualities of high specific strength, high specific modulus, high specific energy absorption, and excellent designability, ultra-high molecular weight polyethylene (UHMWPE) fiber-reinforced composites have gradually replaced traditional materials such as ceramics and steel plates as the main ballistic protection materials. Using an improved test method, the uniaxial tensile tests of UHMWPE fiber-reinforced composites at two strain rates of 10−4 s−1 and 10−2 s−1 and a temperature range from −20 °C to 80 °C are carried out to study the effects of strain rate and temperature on the tensile behavior of UHMWPE fiber-reinforced composites. The experimental results indicate that the tensile responses exhibit nonlinear characteristics and the sensitivity of strain rate and temperature. The yield strength and modulus decrease with increasing temperature and increase with the increase in strain rate. A phenomenological viscoelastic constitutive model composed of a nonlinear spring and a nonlinear Maxwell element is proposed to characterize the temperature and strain rate dependent deformation behavior of UHMWPE fiber-reinforced composites before yielding. The results show that the model can accurately predict the tensile nonlinear viscoelastic responses of UHMWPE fiber-reinforced composites before yielding over a wide temperature range under quasi-static loading.

show abstract

Influence of Varied MWCNTs Dispersion on EMI Shielding, UV Absorption, and Surface Properties of Electroless NiP/MWCNT-Coated UHMWPE Fabric

Biradar,

Kandasamy

2024

Fibers Polym

View full text Add to dashboard Cite

Remarkably improved interfacial adhesion of UHMWPE fibers reinforced composite by constructing a three-dimensional stacked nanoparticles structure at interphase

Cited by 9 publications

References 40 publications

Study on catechol/tetraethylenepentamine and nano zinc oxide co‐modifying ultrahigh molecular weight polyethylene fiber surface to improve interfacial adhesion

Study on catechol/tetraethylenepentamine and nano zinc oxide co‐modifying ultrahigh molecular weight polyethylene fiber surface to improve interfacial adhesion

Temperature and Strain Rate Related Deformation Behavior of UHMWPE Fiber-Reinforced Composites

Influence of Varied MWCNTs Dispersion on EMI Shielding, UV Absorption, and Surface Properties of Electroless NiP/MWCNT-Coated UHMWPE Fabric

Contact Info

Product

Resources

About