Recent Research on the Deformation Behavior of Particle Reinforced Magnesium Matrix Composite: A Review

Deng, Kun-kun; Wang, Cuiju; Nie, Kai-bo; Wang, Xiaojun

doi:10.1007/s40195-019-00872-9

Cited by 62 publications

(9 citation statements)

References 106 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Though the EDS line only qualitatively reflects the evolution of Mn content along inclusion and around steel matrix, this still hints the existence of Mn-depletion zone. In fact, the similar results are also observed in Rare earth-bearing inclusion and Ti-Mg inclusion [8,9], which are used to qualitatively prove the MDZ existence.…”

Section: T Xiangshen Et Al: Relationship Between Mns Precipitation supporting

confidence: 73%

See 1 more Smart Citation

The Relationship between MnS Precipitation and Induced Nucleation Effect of Mg-Bearing Inclusion

Xiangshen

Zhu

Cai

et al. 2018

High Temperature Materials and Processes

View full text Add to dashboard Cite

The relationship between MnS precipitation and induced nucleation effect of Mg-bearing inclusion has been explored through scanning electron microscope and energy dispersive spectrometer (EDS). Results indicate that MnS prefers to precipitate on Mg-bearing inclusions. Statistical analysis suggests that MgAl2O4 and MgO may coexist in inclusion. After etching, it is found that Mg-bearing inclusions can induce the nucleation of intragranular acicular ferrites. Based on EDS line analysis and comparison with Al-Mn-Si-O inclusion in non-Mg-treated sample, this effect can be explained by Mn-depletion zone (MDZ), which is due to the vacancy property and crystal structure of MgAl2O4. In the same sample, similar induced nucleation effect and MDZ are not observed around pure MnS. This comparison implies that the formation of MDZ may be independent of MnS precipitation.

show abstract

Section: T Xiangshen Et Al: Relationship Between Mns Precipitation supporting

confidence: 73%

“…The same tool has been utilized by Wang Xinhua et al [8] and Song bo et al [9] to qualitatively prove the existence of MDZ in Rare earth-bearing inclusion and Ti-Mg inclusion. On theoretical side, the vacancy property and crystal structure of MgAl 2 O 4 are discussed to prove that it's potential to accommodate Mn ions [7].…”

Section: Introductionmentioning

confidence: 99%

The Relationship between MnS Precipitation and Induced Nucleation Effect of Mg-Bearing Inclusion

Xiangshen

Zhu

Cai

et al. 2018

High Temperature Materials and Processes

View full text Add to dashboard Cite

show abstract

“…The correlation between the CNTs distribution, consequent bonding and final mechanical strength of the composites has been the subject of in-depth study by many scientists [35,65,67,[76][77][78][79][80]. Here, the different BM conditions (low-and high-energy) affecting the final properties of AMCs are illustrated in order to optimize the different milling strategies.…”

Section: Flake Powder Metallurgy Via Shift Speed-ball Milling (Fpm-ssbm)mentioning

confidence: 99%

Progress of Flake Powder Metallurgy Research

Sadeghi

Cavaliere

2021

Metals

View full text Add to dashboard Cite

This paper reviewed several recent progresses of the new powder metallurgy technology known as flake powder metallurgy (FPM) including different processing routes, conventional FPM (C-FPM), slurry blending (SB), shift-speed ball milling (SSBM), and high-shear pre-dispersion and SSBM (HSPD/SSBM). The name of FPM was derived from the use of flake metal powders obtained by low-speed ball milling (LSBM) from spherical powder. In this case, the uniformity of reinforcement distribution leads to increased strength and ductility. Powder is the basic unit in PM, especially advanced PM, and its control is key to various new PM technologies. The FPM is a typical method for finely controlling the powder shape through low-energy ball milling (LEBM) to realize the preparation of advanced material structures. The present paper represents a review of the main results of research on FPM and indicates the potential for future studies devoted to the optimization of this processing route.

show abstract

“…Nevertheless, the absolute strength and elasticity modulus of magnesium alloys are relatively low, which could not meet the requirements of practical applications [6][7][8][9]. As a consequence, hard ceramic particles are always incorporated with magnesium alloys to fabricate magnesium matrix composites with improved mechanical properties [10][11][12][13][14][15][16].…”

Section: Introductionmentioning

confidence: 99%

Effect of Necklace-Type Distribution of SiC Particles on Dry Sliding Wear Behavior of As-Cast AZ91D/SiCp Composites

Sun

Liu

et al. 2020

Crystals

View full text Add to dashboard Cite

In this study, the dry sliding wear behaviors of SiC particle reinforced AZ91D matrix composites fabricated by stirring casting method were systematically investigated. The SiC particles in as-cast composites exhibited typical necklace-type distribution, which caused the weak interface bonding between SiC particles and matrix in particle-segregated zones. During dry sliding at higher applied loads, SiC particles were easy to debond from the matrix, which accelerated the wear rates of the composites. While at the lower load of 10 N, the presence of SiC particles improved the wear resistance. Moreover, the necklace-type distribution became more evident with the decrease of particle sizes and the increase of SiC volume fractions. Larger particles had better interface bonding with the matrix, which could delay the transition of wear mechanism from oxidation to delamination. Therefore, composites reinforced by larger SiC particles exhibited higher wear resistance. Similarly, owing to more weak interfaces in the composites with high content of SiC particles, more severe delamination occurred and the wear resistance of the composites was impaired.

show abstract

Recent Research on the Deformation Behavior of Particle Reinforced Magnesium Matrix Composite: A Review

Cited by 62 publications

References 106 publications

The Relationship between MnS Precipitation and Induced Nucleation Effect of Mg-Bearing Inclusion

The Relationship between MnS Precipitation and Induced Nucleation Effect of Mg-Bearing Inclusion

Progress of Flake Powder Metallurgy Research

Effect of Necklace-Type Distribution of SiC Particles on Dry Sliding Wear Behavior of As-Cast AZ91D/SiCp Composites

Contact Info

Product

Resources

About