Rational design of composite interlayer for diffusion bonding of tungsten–steel joints

Cai, Qingshan; Zhu, Wentan; Ma, Yunzhu; Liu, Wensheng; Pang, Xinkuan; Liang, Chaoping

doi:10.1016/j.ijrmhm.2017.10.002

Cited by 43 publications

(5 citation statements)

References 22 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…As it was shown in [45], ductile materials like Cu and Ni reduce residual stresses more efficiently than materials with a medium CTE (V, Ta). Pure copper as a brazing alloy was first presented in [33], though copper alloys had been widely investigated before.…”

Section: The Latest Progress Made In Tungsten/steel Brazingmentioning

confidence: 72%

Overview of the Mechanical Properties of Tungsten/Steel Brazed Joints for the DEMO Fusion Reactor

Bachurina

Vorkel

Сучков

et al. 2021

Metals

View full text Add to dashboard Cite

A Demonstration (DEMO) thermonuclear reactor is the next step after the International Thermonuclear Experimental Reactor (ITER). Designs for a DEMO divertor and the First Wall require the joining of tungsten to steel; this is a difficult task, however, because of the metals’ physical properties and necessary operating conditions. Brazing is a prospective technology that could be used to solve this problem. This work examines a state-of-the-art solution to the problem of joining tungsten to steel by brazing, in order to summarize best practices, identify shortcomings, and clarify mechanical property requirements. Here, we outline the ways in which brazing technology can be developed to join tungsten to steel for use in a DEMO application.

show abstract

Section: The Latest Progress Made In Tungsten/steel Brazingmentioning

confidence: 72%

Overview of the Mechanical Properties of Tungsten/Steel Brazed Joints for the DEMO Fusion Reactor

Bachurina

Vorkel

Сучков

et al. 2021

Metals

View full text Add to dashboard Cite

show abstract

“…The low activation metal of vanadium has a CTE of [43], located in between those of RAFMs [47] and W [48], suitable for this interlayer application. When used together with Fe-based amorphous alloys for brazing, the formation of brittle σ-VFe phase at their interface is hardly avoided.…”

Section: Methodsmentioning

confidence: 99%

“…The joining of W and RAFMs has been realised mainly by brazing [13][14][15][16][17][18][19][20][21][22][23][24][25]45,46] and solid-state diffusion bonding [16,17,[26][27][28][30][31][32][33][34][35][36][37][38][39][40][41][42][43][44][45][46]. Brazing is suitable for joining components with complex geometries.…”

Section: Introductionmentioning

confidence: 99%

“…The effective joining also requires minimal changes in the microstructure and material properties of W and RAFMs. Various joining methods and filler materials have been extensively studied for the fabrication of high-performance W/RAFMs joints [13-46].…”

Section: Introductionmentioning

confidence: 99%

“…The joining of W and RAFMs has been realised mainly by brazing [13-25,45,46] and solid-state diffusion bonding [16,17,26-28,30-46]. Brazing is suitable for joining components with complex geometries.…”

Section: Introductionmentioning

confidence: 99%

See 2 more Smart Citations

Tungsten/reduced activation ferritic–martensitic steel joints made with an Fe–Si–B amorphous filler

Wang

Lian

Feng

et al. 2021

Materials Science and Technology

View full text Add to dashboard Cite

The joining of Tungsten (W) and reduced activation ferritic–martensitic steel (RAFMs) is crucial to the fabrication of divertors in future fusion reactors. In this work, an Fe75.0Si8.33B16.67 (at.-%) amorphous filler and iron interlayer are considered for brazing W and RAFMs. Crack-free joints in both the as-brazed and post joining heat treatment (PJHT) states have been obtained by short-time vacuum brazing at 1230°C. The bonding seams of the joints are composed of an α-Fe matrix, fine FeWB and Fe3B particles. The PJHT joint exhibits a high strength of 310 MPa and room temperature plasticity. The strong and tough joint would be appealing in its thermal cycling and thermal shock performance.

show abstract

Effect of Bonding Temperature on the Interfacial Microstructure and Mechanical Properties of W/Steel Joints Diffusion-Bonded with a CoFeNi Interlayer

Wang,

Tao,

Liang

et al. 2024

JOM

View full text Add to dashboard Cite

Rational design of composite interlayer for diffusion bonding of tungsten–steel joints

Cited by 43 publications

References 22 publications

Overview of the Mechanical Properties of Tungsten/Steel Brazed Joints for the DEMO Fusion Reactor

Overview of the Mechanical Properties of Tungsten/Steel Brazed Joints for the DEMO Fusion Reactor

Tungsten/reduced activation ferritic–martensitic steel joints made with an Fe–Si–B amorphous filler

Effect of Bonding Temperature on the Interfacial Microstructure and Mechanical Properties of W/Steel Joints Diffusion-Bonded with a CoFeNi Interlayer

Contact Info

Product

Resources

About