Preparation and Properties of Electroless Deposited Ni-Sn-P Ternary Alloy Coatings

Zhu, Shufang; Wu, Yu Cheng

doi:10.4028/www.scientific.net/amr.189-193.455

Cited by 4 publications

(2 citation statements)

References 14 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The erosion tester was shown in the paper has been published 13 . The substrate material is 20 steel, the dimension of 20 steel samples is 15 mm × 25 mm × 3 mm.…”

Section: Preparation and Characterization Of Electroless Deposited Nimentioning

confidence: 99%

Preparation and Characterization of Electroless Deposited Ni-Zn-P-TiO2(N) Composite Coating

Zhu¹,

Chuan-Qi²,

Wu³

2013

Asian J. Chem.

View full text Add to dashboard Cite

Nitrogen doped nano anatase TiO2 particles were prepared by nitriding treatment. The Ni-Zn-P-TiO2(N) composite coatings were prepared by adding nano TiO2(N) to electroless plating Ni-Zn-P alloy bath. The composite coatings were characterized and tested. The results show that, the maximum deposition rate occurs at 1 g dm-3 content of TiO2(N). The as-plated Ni-Zn-P-TiO2(N) composite coating consists facecentered-cubic Ni-Zn-P alloy and anatase type TiO2(N). The percentage weight of zinc, phosphorus and titanium in the composite are 6.94, 8.15 and 2.56 % respectively. The Ni-Zn-P-nano TiO2(N) composite coatings have higher hardness value, better erosion property and photodegradation effect than those of Ni-Zn-P-TiO2 composite coatings.

show abstract

“…The erosion tester was shown in the paper has been published 13 . The substrate material is 20 steel, the dimension of 20 steel samples is 15 mm × 25 mm × 3 mm.…”

Section: Preparation and Characterization Of Electroless Deposited Nimentioning

confidence: 99%

Preparation and Characterization of Electroless Deposited Ni-Zn-P-TiO2(N) Composite Coating

Zhu¹,

Chuan-Qi²,

Wu³

2013

Asian J. Chem.

View full text Add to dashboard Cite

show abstract

“…The introduction of the second element depends on the application of the coatings to meet some special demands. The electroless Ni–Sn–P ternary alloy coatings with a uniform structure, low friction coefficient, excellent corrosion, and oxidation resistance seem to be of cardinal significance …”

Section: Introductionmentioning

confidence: 99%

Microstructure and properties of open‐cell Ni–Sn–P alloy foams prepared by electroless plating

Liu

Gan

Zhou

2019

Materials & Corrosion

View full text Add to dashboard Cite

In this study, open-cell Ni-Sn-P alloy foams were prepared by electroless plating. The influence of tin content on the surface morphology and properties of Ni-Sn-P alloy foams were investigated. The surface structure of Ni-Sn-P alloy foams became more uniform and compact with the increase of Sn content.The X-ray diffraction result showed that Ni-Sn-P alloy foams gradually transformed from an amorphous structure into crystallization with the increase of heat-treatment temperature. The introduction of Sn significantly enhanced the corrosion resistance of Ni-P coatings in 3.5 wt% NaCl solution, the corrosion current density decreased from 5.022 to 0.805 μA/cm 2 and the corrosion potential shifted positively from −0.423 to −0.294 V after adding 5.96 wt% Sn to Ni-P coatings. However, the corrosion resistance of Ni-Sn-P foams was deteriorated after heat treatment. Adding Sn to the Ni-P system slightly weakened the compressive strength of Ni-P binary foams. Nevertheless, significant improvement in the antioxidant performance of Ni-Sn-P alloy foams was indicated by the reduction of the mass change rate in that the mass change rate of Ni-P foams obviously reduced from 5.15% to 0.25% after adding 5.96 wt% Sn. K E Y W O R D Scorrosion resistance, electroless plating, heat treatment, Ni-Sn-P alloy foams, oxidation resistance

show abstract

Effect of Heat Treatment on Slurry Erosion Wear Resistance of Amorphous Ni-P Electrodeposits

Yang

Zhao

et al. 2012

Tribology Transactions

View full text Add to dashboard Cite

Preparation and Properties of Electroless Deposited Ni-Sn-P Ternary Alloy Coatings

Cited by 4 publications

References 14 publications

Preparation and Characterization of Electroless Deposited Ni-Zn-P-TiO2(N) Composite Coating

Preparation and Characterization of Electroless Deposited Ni-Zn-P-TiO2(N) Composite Coating

Microstructure and properties of open‐cell Ni–Sn–P alloy foams prepared by electroless plating

Effect of Heat Treatment on Slurry Erosion Wear Resistance of Amorphous Ni-P Electrodeposits

Contact Info

Product

Resources

About