Plywood Made from Plasma-Treated Veneers: Investigation of Performance Differences between Plasma-Pretreated and Untreated Beech Veneers at Comparable Melamine Resin Load

Wascher, Richard; Avramidis, Georg; Viöl, Wolfgang

doi:10.3390/f12101423

Cited by 3 publications

(1 citation statement)

References 16 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The MOE may decrease due to factors such as reduced mechanical interlocking, increased void spaces, and inadequate penetration [60]. The reduction in lignin particle sizes can also impact the MOR by weakening bonding, increasing water absorption, and making it more vulnerable to defects [102,103]. To mitigate these reductions, particleboard manufacturers can consider using a well-balanced combination of different lignin particle sizes, incorporating other additives or modifiers, and conducting thorough testing and quality control [104,105].…”

Section: Mechanical Properties Of Bark Particleboard With Various Par...mentioning

confidence: 99%

Properties of Bark Particleboard Bonded with Demethylated Lignin Adhesives Derived from <i>Leucaena leucocephala</i> Bark

Salim,

Asik,

Sarjadi

2024

JRM

View full text Add to dashboard Cite

Lignin extraction from bark can maximize the utilization of biomass waste, offer cost-effectiveness, and promote environmental friendliness when employed as an adhesive material in bark particleboard production. Particles of fine (0.2 to 1.0 mm), medium (1.0 to 2.5 mm), and coarse (2.5 to 12.0 mm) sizes, derived from the bark of Leucaena leucocephala, were hot-pressed using a heating plate at 175°C for 7 min to create single-layer particleboards measuring 320 mm × 320 mm × 10 mm, targeting a density of 700 kg/m 3 . Subsequently, the samples were trimmed and conditioned at 20°C and 65% relative humidity. In this study, we compared bark particleboard bonded with urea formaldehyde (UF) adhesive to fine-sized particleboard bonded with demethylated lignin adhesive. The results indicated that bark particleboards utilizing demethylated lignin and UF adhesives exhibited similar qualities. Coarse particleboard showed differences in modulus of elasticity (MOE) and modulus of rupture (MOR), while medium-sized particles exhibited significant variations in moisture content (MC) and water absorption (WA). Furthermore, the thickness swelling of coarse and medium-sized particles under wet and oven-dried conditions exhibited notable distinctions. Overall, the demethylated lignin adhesive extracted from L. leucocephala bark demonstrated similar quality to UF adhesive, with particle size correlating inversely to the strength of the bark particleboard. KEYWORDSBark particleboard properties; demethylated lignin; lignin adhesives; Leucaena leucocephala; bark particles Nomenclature UF Urea formaldehyde MOE Modulus of elasticity MOR Modulus of rupture MC Moisture content TS Thickness swelling TS-Wet Thickness swelling from wet to oven dry conditions. TS-AD Thickness swelling from air-dry to oven dry conditions. IB Internal bonding

show abstract

Section: Mechanical Properties Of Bark Particleboard With Various Par...mentioning

confidence: 99%

Properties of Bark Particleboard Bonded with Demethylated Lignin Adhesives Derived from <i>Leucaena leucocephala</i> Bark

Salim,

Asik,

Sarjadi

2024

JRM

View full text Add to dashboard Cite

show abstract

A review of application, modification, and prospect of melamine foam

Wang,

Chen,

et al. 2023

Nanotechnology Reviews

View full text Add to dashboard Cite

Melamine foam (MF), a promising development in light materials, finds application in construction, agriculture, aviation, transportation, electronic message, and other fields due to its excellent thermal insulation performance, sound absorption and noise reduction capabilities, safety and health benefits, as well as easy processing. However, its own shortcomings such as hardness, poor toughness, fragility, and slag removal greatly limit its application scope. In this review, a survey of the literature from two aspects of toughening of melamine resin and regulation of MF pore structure are reviewed to explore the research progress of toughening modification of MF. The principle, merit, and demerit of different modification methods are analyzed. In addition, owing to the extensive literature available, this article also summarizes the representative achievements of the nanotechnology modification of MF derivatives (carbon foam and carbon aerogel). Eventually, based on an assessment of current application status for both MF and its derivatives while considering existing challenges in their modification processes using nanotechnology approaches, we discuss future prospects for their application.

show abstract

The synergistic effect of microwave drying and plasma surface treatments on the wettability of green wood

Ganguly¹,

Žigon²,

Srinivasa³

et al. 2022

les-wood

View full text Add to dashboard Cite

In spite of being both a one-step solution to several problems associated with woodworking and also energy efficient, the application of microwave (MW) modification in wood research has remained very limited and this promising method has practically no use in wood industries across the globe. Research done so far in this field primarily sheds light on its potential in enhancing wood permeability, treatability and uniform wood drying. While MW treatments are mostly used on wet or green wood, another modification technique, plasma, has potential benefits to synergistically enhance the effects of MW treatment, but so far has not been applied on wet or green wood specimens. This study takes a first step to investigate the effects of plasma treatments (PT) on green wood specimens, as well as combinations of MW and plasma treatments. As a preliminary study, the methodology focuses on water contact angle measurements, since these are most commonly used as indicators for surface modifications in industrial applications. An exponential time dependence was found for the contact angle on the investigated samples of Norway spruce (Picea abies Karst.). Initial contact angles after droplet deposition increased due to drying and migration of organic molecules during treatments. In comparison with the literature, the effect of plasma was significantly less pronounced on wet wood specimens. The initial contact angles showed the lowest statistical variations after MW treatment, whereas plasma increased inhomogeneities. The final contact angles on treated specimens was lowest for PT-only specimens as well as specimens treated with plasma after MW. In contrast to the initial contact angles, the final contact angles showed the lowest variations after PT. Wetting rates were insignificantly improved by plasma, with reduced statistical variations after all treatments.

show abstract

Plywood Made from Plasma-Treated Veneers: Investigation of Performance Differences between Plasma-Pretreated and Untreated Beech Veneers at Comparable Melamine Resin Load

Cited by 3 publications

References 16 publications

Properties of Bark Particleboard Bonded with Demethylated Lignin Adhesives Derived from <i>Leucaena leucocephala</i> Bark

Properties of Bark Particleboard Bonded with Demethylated Lignin Adhesives Derived from <i>Leucaena leucocephala</i> Bark

A review of application, modification, and prospect of melamine foam

The synergistic effect of microwave drying and plasma surface treatments on the wettability of green wood

Contact Info

Product

Resources

About