Performance evaluation and material optimization of Micro-surfacing based on cracking and rutting resistance

Zhang, Ke; Xie, Xiangbing; Yao, Xiaoguang

doi:10.1016/j.conbuildmat.2019.02.066

Cited by 46 publications

(16 citation statements)

References 1 publication

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Most of the asphalt was found in the mixture at high temperatures when the migration occurred, resulting in the formation of a dense bleeding on the surface of the microsurfacing. The depth of structure is significantly reduced, which affects its rutting resistance and appearance [ 39 ]. Although the microsurfacing mixture is thinner, the requirements for the high-temperature resistance of the emulsified asphalt should not be reduced, especially for microsurfacing overlays.…”

Section: Resultsmentioning

confidence: 99%

Validation of Adhesive and Temperature Property Characteristics of Microsurfacing by Performance-Based Mixture Design Approach

et al. 2021

View full text Add to dashboard Cite

Performance-based mixture design of microsurfacing offers a promising solution to the best application of asphalt emulsions. The presented study investigated a novel approach to evaluate the spalling resistance and high and low-temperature resistance of microsurfacing. The laboratory tests, including mixture bond strength (MBS), driving wheel pavement analyzer (DWPA), multi-stress creep recovery (MSCR), load wheel rutting (LWR), and single edge notch beam (SENB) were conducted to characterize the performance-related properties; the response surface method (RSM) was used to obtain the optimal proportions of the mixture. According to the experimental results, the performance-based mixture design method improves the comprehensive performance of microsurfacing, such as adhesion at high and low temperatures. The results of RSM show that temperature is the most important factor that affects the adhesion of mixture. There is a strong correlation between adhesive and temperature performance detected by different test methods. Due to different chemical mechanisms caused by cement and emulsified asphalt, the high-temperature performance index of the microsurfacing mixture is lower than that of HMA. Furthermore, the low-temperature resistance is analyzed and suggested indicator is proposed.

show abstract

Section: Resultsmentioning

confidence: 99%

Validation of Adhesive and Temperature Property Characteristics of Microsurfacing by Performance-Based Mixture Design Approach

et al. 2021

View full text Add to dashboard Cite

show abstract

“…The analysis results are shown in Tables 6 and 7. The greater the sum of the mean square deviations of a factor is, the more significant the influence of this factor is [58]. It can be seen that when the F/A ratio is 0.8-1.4, the UV irradiation intensity has a significant impact on the SAI value, while when the F/A ratio is 1.2-1.6, the mineral powder content in the F/A ratio has a significant impact on the SAI value.…”

Section: Analysis Of Variance (Anova)mentioning

confidence: 99%

Influence of the Mineral Powder Content on the Asphalt Aging Resistance in High-Altitude Areas Based on Indoor Ultraviolet Light Tests

Xie

Duan

et al. 2020

Materials

Self Cite

View full text Add to dashboard Cite

Intense ultraviolet irradiation is an important environmental factor affecting the service performance of asphalt mixtures in high-altitude areas, and the asphalt mortar is the main factor affecting the durability of asphalt mixtures. It is of great theoretical significance and engineering value to study the performance of the asphalt mortar at medium and low temperatures under ultraviolet irradiation. Therefore, this paper focuses on the evolution of the effect of the filler content on the rheological properties of different asphalt materials at low and medium temperatures under quantitative UV irradiation. Taking the average amount of UV irradiation observed annually in Northwest China as the indoor aging condition, the matrix asphalt mortar and modified asphalt mortar with different mass ratios of asphalt mortar are selected for indoor aging tests. Physical property tests, low-temperature performance tests, and dynamic shear rheological tests are carried out. The effects of the UV irradiation intensity and mineral powder content on the low temperature performance of the asphalt mortar are studied by variance analysis method, and the reasonable mass ratio range of the asphalt mortar under UV irradiation is proposed based on the standard residual square sum (STRSS) method. The results show that the temperature sensibility and low-temperature deformation energy significantly decrease with the increase in the filler content, while the values of the softening point, fatigue factor (G*sin δ), and creep stiffness modulus of the asphalt mortar increase. In addition, the variance analysis of the creep stiffness modulus aging index (SAI) shows that the ultraviolet radiation intensity has a significant impact on the performance of the asphalt mortar. When the mineral powder content is less than 40%. When the filler content is greater than 40%, the filler content effects the performance of the asphalt mortar. According to the standard residual square sum (STRSS) method, the best mass ratio of the base asphalt mortar is 1.096, and the best mass ratio of the modified asphalt mortar is 0.9091.

show abstract

“…The results indicated that basalt fiber had the prime reinforcement and SBS modified asphalt was found to be well reinforced with fiber. Luo et al [27] evaluated the enhancement impact of SBS and basalt fiber on anti-rutting and anti-cracking of modified asphalt mixture by the Hamburg wheel track test and the low temperature bending test, respectively. Kou et al [28] selected basalt fiber to reinforce asphalt materials incorporating of SBS polymer, and they found that asphalt materials incorporating of SBS polymer and basalt fiber can make use of both advantages of additives [29][30][31].…”

Section: Introductionmentioning

confidence: 99%

Master Curve Establishment and Complex Modulus Evaluation of SBS-Modified Asphalt Mixture Reinforced with Basalt Fiber Based on Generalized Sigmoidal Model

et al. 2020

View full text Add to dashboard Cite

Basalt fiber has been proved to be a good modified material for asphalt mixture. The performance of basalt fiber modified asphalt mixture has been widely investigated by extensive researches. However, most studies focused on ordinary static load tests, and less attention was paid to the dynamic mechanical response of asphalt mixture incorporating with basalt fiber. This paper aims to establish the master curve of complex modulus of asphalt mixture incorporating of styrene-butadiene-styrene (SBS) polymer and basalt fiber using the generalized Sigmoidal model. Both loading frequency and temperature were investigated for dynamic mechanical response of asphalt mixture with basalt fiber. In addition, based on the time-temperature superposition principle, the master curves of complex modulus were constructed to reflect the dynamic mechanical response at an extended reduced frequency range at an arbitrary temperature. Results indicated that the generalized Sigmoidal model in this paper could better reflect the dynamic mechanical response accurately with correlation coefficients above 0.97, which is utilized to predict the dynamic mechanical performances accurately. Simultaneously, the modulus values exhibit an increasing trend with loading frequency and decrease versus temperature. However, the phase angle values showed different trends with frequency and temperature.

show abstract

Performance evaluation and material optimization of Micro-surfacing based on cracking and rutting resistance

Cited by 46 publications

References 1 publication

Validation of Adhesive and Temperature Property Characteristics of Microsurfacing by Performance-Based Mixture Design Approach

Validation of Adhesive and Temperature Property Characteristics of Microsurfacing by Performance-Based Mixture Design Approach

Influence of the Mineral Powder Content on the Asphalt Aging Resistance in High-Altitude Areas Based on Indoor Ultraviolet Light Tests

Master Curve Establishment and Complex Modulus Evaluation of SBS-Modified Asphalt Mixture Reinforced with Basalt Fiber Based on Generalized Sigmoidal Model

Contact Info

Product

Resources

About