Pengaruh Suhu dan Waktu Vulkanisasi Terhadap Sifat Kekerasan dan Visual Produk Footstep Sepeda Motor

Delvitasari, Febrina; Maryanti, Maryanti

doi:10.34128/jtai.v7i2.123

Cited by 2 publications

(2 citation statements)

References 2 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…First, prepare materials such as natural rubber, synthetic rubber and other chemicals to be mixed using two roll mixing so that they are evenly mixed, after that you will get a very thin mixture called compound [14].…”

Section: Compound Manufacturingmentioning

confidence: 99%

Impact of sulfur compounds on motorbike wheel damper rubber manufacturing materials with 3 Phr, 4 Phr, and 6 Phr compositions

Pramuko Ilmu Purboputro,

Sartono Putro,

Subroto

2024

jttm

View full text Add to dashboard Cite

Rubber force is a simple but important thing for vehicles. This component is located in the rear wheel drum which is directly connected to the gear. Many factors influence the damage to this component. This research aims to determine how much influence stearic acid has on the hardness and tensile strength values of the lifting rubber compound. The materials used to make the compound are rubber smoked sheet (RSS) and synthetic rubber mixed with the chemicals stearic acid, black carbon white oil, ZnO, paraffin wax, MBTS, comaron resin and sulfur. These ingredients are mixed using two roll mixing until they combine and form a compound sheet. To determine the maturation time of rubber, a rheometer process is carried out. The next process is vulcanization of rubber using a mold that is pressed at a temperature of 1600C and a pressure of 150 psi. Tensile testing uses rubber testing equipment with SNI ISO 37: 2015 (IDT–2011) standards. Hardness testing uses a tool with a Shore A hardness tester scale with ISO 7619–1:2010 standards. Based on the results of the tests carried out, the addition of sulfur has a very significant effect on the hardness value and tensile strength value. For the hardness value of compound 3 with a sulfur composition of 6 phr, it has the highest hardness, namely 77 Shore A and the lowest value is composition 1 with a hardness value of 65.6 Shore A. The highest tensile strength value is 15,394 N/mm2 in composition 1 and the lowest value is in composition 3 with a value of 11.44 N/mm2

show abstract

Section: Compound Manufacturingmentioning

confidence: 99%

Impact of sulfur compounds on motorbike wheel damper rubber manufacturing materials with 3 Phr, 4 Phr, and 6 Phr compositions

Pramuko Ilmu Purboputro,

Sartono Putro,

Subroto

2024

jttm

View full text Add to dashboard Cite

show abstract

“…In one study, it was stated that peak torque occurs at engine speed between 4500 rpm and 6000 rpm. The two torque peaks are produced by a combination of reflected pressure waves at the end of the header pipe and in the exhaust manifold [14].…”

Section: Figure 1 Tec On a Bajaj Auto Limited Motorbikementioning

confidence: 99%

Experimental study of motor cycle performance with exhaust manifold using torque expansion chamber

Subroto,

Sartono Putro,

Pramuko Ilmu Purboputro

2024

jttm

View full text Add to dashboard Cite

The Motorcycle performance can be improved by modifying the intake manifold and exhaust manifold. In this research, the exhaust manifold was modified using a Torque Expansion Chamber (TEC), namely adding a tube to the exhaust manifold with a certain geometry and dimensions so that the heat carried by the exhaust gas is retained and does not directly escape through the exhaust. This test aims to determine the performance of a motorbike with a modified exhaust manifold by adding 250 mm tubular TEC. TEC installation with placement at 40%, 50%, and 60% of the exhaust manifold length. Engine performance including torque, power and specific fuel consumption is measured using the Dyno Test. The research results show that the use of the Torque Expansion Chamber has an effect on motorbike performance. Highest torque with 50% TEC placement and 60% TEC placement at 5000 rpm. Highest power with 50% TEC placement and 60% TEC placement at 6000 rpm to 6500 rpm. Lowest specific fuel consumption with 50% TEC placement at 6000 rpm

show abstract

Pengaruh Suhu dan Waktu Vulkanisasi Terhadap Sifat Kekerasan dan Visual Produk Footstep Sepeda Motor

Cited by 2 publications

References 2 publications

Impact of sulfur compounds on motorbike wheel damper rubber manufacturing materials with 3 Phr, 4 Phr, and 6 Phr compositions

Impact of sulfur compounds on motorbike wheel damper rubber manufacturing materials with 3 Phr, 4 Phr, and 6 Phr compositions

Experimental study of motor cycle performance with exhaust manifold using torque expansion chamber

Contact Info

Product

Resources

About