Partial Current Harmonic Compensation in Dual Three-Phase PMSMs Considering the Limited Available Voltage

Karttunen, Jussi; Kallio, Samuli; Honkanen, Jari; Peltoniemi, Pasi; Silventoinen, Pertti

doi:10.1109/tie.2016.2618786

Cited by 50 publications

(33 citation statements)

References 33 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…6 remains unaltered, the amplitude of the fifth and seventh current harmonics increases to 39.19% and 15.14%, respectively. Although these harmonics can be compensated by the control system, an oversized dc‐link voltage is required [13]. In order to compare both designs at rated conditions, the efficiency and the TWD of current, EMF and torque are given in Table 5.…”

Section: Fea Resultsmentioning

confidence: 99%

Design of a six‐phase asymmetrical permanent magnet synchronous generator for wind energy applications

Goncalves¹,

Cruz²,

Mendes³

2019

J. eng.

View full text Add to dashboard Cite

Section: Fea Resultsmentioning

confidence: 99%

Design of a six‐phase asymmetrical permanent magnet synchronous generator for wind energy applications

Goncalves¹,

Cruz²,

Mendes³

2019

J. eng.

View full text Add to dashboard Cite

“…Although virtual vectors impose zero x-y voltage components over a sampling period, x -y currents with considerable magnitude may continue to circulate in the stator windings due to machine asymmetries, deadtime effects in the power switches of the VSIs or, in the case of PMSMs, the back-EMF harmonics due to the non-sinusoidal shape of PMs [117][118][119]. Since the elimination of these current harmonics requires the application of non-zero x-y voltages, the concept of dual virtual vectors was introduced in Reference [120].…”

Section: Bi-subspace Predictive Current Control Based On Virtual Vectorsmentioning

confidence: 99%

Finite Control Set Model Predictive Control of Six-Phase Asymmetrical Machines—An Overview

2019

View full text Add to dashboard Cite

Recently, the control of multiphase electric drives has been a hot research topic due to the advantages of multiphase machines, namely the reduced phase ratings, improved fault tolerance and lesser torque harmonics. Finite control set model predictive control (FCS-MPC) is one of the most promising high performance control strategies due to its good dynamic behaviour and flexibility in the definition of control objectives. Although several FCS-MPC strategies have already been proposed for multiphase drives, a comparative study that assembles all these strategies in a single reference is still missing. Hence, this paper aims to provide an overview and a critical comparison of all available FCS-MPC techniques for electric drives based on six-phase machines, focusing mainly on predictive current control (PCC) and predictive torque control (PTC) strategies. The performance of an asymmetrical six-phase permanent magnet synchronous machine is compared side-by-side for a total of thirteen PCC and five PTC strategies, with the aid of simulation and experimental results. Finally, in order to determine the best and the worst performing control strategies, each strategy is evaluated according to distinct features, such as ease of implementation, minimization of current harmonics, tuning requirements, computational burden, among others.

show abstract

“…However, the cost will be increased, so it is always preferred to retain the conventional design of the inverter where there are only current sensors. Observers can be adopted to estimate unmeasured variables and applied as the feedback of the controllers, which has been researched in the literature [10,11,[14][15][16][17][18][19][20]. In particular, in [10,11], state observers in the rotating reference frame were presented to estimate the variables for the motor equipped with an LC filter.…”

Section: Introductionmentioning

confidence: 99%

Sliding mode control with open‐switch fault diagnosis and sensorless estimation based on PI observer for PMSM drive connected with an LC filter

Wang

Zou

2020

IET Power Electronics

View full text Add to dashboard Cite

In some cases, LC filters are installed between the inverters and motors to suppress the adverse effects of pulse width modulation. However, some techniques should be modified, because the mathematical model of the drive system is changed by the LC filter and the sensors on the inverter output cannot measure some necessary variables. In this study, a multipurpose proportional-integral (PI) observer is proposed at first. The type of observer depends on whether the position sensor is equipped. A sliding mode controller for the LC filter based on the observer is presented, therefore improving the dynamic performance. Furthermore, if the position sensor of the rotor is equipped, an open-switch fault diagnostic method is realised by means of the PI observer; if the position sensor is not equipped, the sensorless estimation is realized. The proposed strategies were realised without any additional current/voltage sensors. Experimental results verified the effectiveness of the proposed strategies.

show abstract

Partial Current Harmonic Compensation in Dual Three-Phase PMSMs Considering the Limited Available Voltage

Cited by 50 publications

References 33 publications

Design of a six‐phase asymmetrical permanent magnet synchronous generator for wind energy applications

Design of a six‐phase asymmetrical permanent magnet synchronous generator for wind energy applications

Finite Control Set Model Predictive Control of Six-Phase Asymmetrical Machines—An Overview

Sliding mode control with open‐switch fault diagnosis and sensorless estimation based on PI observer for PMSM drive connected with an LC filter

Contact Info

Product

Resources

About