Optimizing process parameters of hot-bar soldering process through quality function deployment and Taguchi method

Jeang, Angus; Chung, Chien‐Ping; Chen, Chung-Wei; Li, Huan-Chung

doi:10.1016/j.jmatprotec.2008.07.007

Cited by 12 publications

(6 citation statements)

References 6 publications

(5 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In order to conduct an analysis of the relative importance of each factor more systematically, an analysis of variance (ANOVA) was applied to the data. The main objective of ANOVA is to extract from the results how much variations each factor causes relative to the total variation observed in the result [15,16]. From the results of ANOVA in Table 4, iron had the largest variance, which indicated that the most influential factor was the initial iron concentration.…”

Section: Parametermentioning

confidence: 99%

Bioxidative dissolution of cinnabar by iron-oxidizing bacteria

Wang¹,

Yang²,

Li³

et al. 2013

Biochemical Engineering Journal

View full text Add to dashboard Cite

Section: Parametermentioning

confidence: 99%

Bioxidative dissolution of cinnabar by iron-oxidizing bacteria

Wang¹,

Yang²,

Li³

et al. 2013

Biochemical Engineering Journal

View full text Add to dashboard Cite

“…The welding temperature, welding time, and welding pressure are the key factors that affect the forming quality of HBS [9]. The welding temperature and welding time directly affect the welding heat.…”

Section: Introductionmentioning

confidence: 99%

Effect of Servo-Pressurized Mode on Soldering Process Characteristics of Micro-Parts

Zhang

Yang

et al. 2022

IEEE Access

View full text Add to dashboard Cite

To solve the problems of high pressure fluctuations and uncontrollable process pressure in the traditional pneumatic pressurized hot-bar solder welding process, a servo-pressurized system with high dynamic pressure and displacement responses was designed during this study using a servo motor. Focusing on the connection requirements between narrow-gap coaxial cables and printed circuit boards, the overall scheme of the system was designed, the dynamic characteristics of the mechanical structure of the system were analyzed, the hardware and software design processes for the control system were described, and a stage-type pressure-following motion control scheme for the hot bar suitable for solder-forming control was proposed. By conducting solder welding tests on narrow-gap coaxial cables with and without the control scheme, the welding process characteristics and joint qualities after welding were analyzed. The results show that when using the control scheme for solder welding, the welding pressure changes during the solder welding process trended first from a rapid increase to a slow decrease, then to a rapid decrease, to a slow decrease, and finally to a near zero value. "Soft contact" pressurization between the hot bar and the welded workpieces was achieved, the pressure fluctuations were reduced, and better surface and higher strengths were obtained for the welded joints.INDEX TERMS Hot-bar soldering, servo-pressurized system, stage-type pressure-following, solder welding, process characteristics analysis.

show abstract

“…The optimization of injection molding process for friction properties of fiber-reinforced polybutylene terephthalate was done using taguchi method and principal component analysis [21]. The combined quality function deployment (QFD) and the taguchi method to analyze the produced quality characteristics and to optimize the process parameters was applied [22]. The CO 2 continuous laser welding process was successfully applied and optimized for joining a dissimilar AISI 316 stainless-steel and AISI 1009 low carbon steel plates [23].…”

Section: Introductionmentioning

confidence: 99%

Application of Taguchi and FEM to Explore the Surface Properties of Glass Using USM Process

Kumar¹

2013

AJME

View full text Add to dashboard Cite

The FEM analysis of ultrasonic tool has been done in addition to surface roughness of machined samples using ultrasonic machining process have been presented. The experimental conditions were designed by using DOE approach. The analysis of results has been done using the MINITAB 14.0 software and results obtained are validated by conducting the confirmation experiments. The F-test and P-value has been applied to determine the significant parameters.

show abstract

Optimizing process parameters of hot-bar soldering process through quality function deployment and Taguchi method

Cited by 12 publications

References 6 publications

Bioxidative dissolution of cinnabar by iron-oxidizing bacteria

Bioxidative dissolution of cinnabar by iron-oxidizing bacteria

Effect of Servo-Pressurized Mode on Soldering Process Characteristics of Micro-Parts

Application of Taguchi and FEM to Explore the Surface Properties of Glass Using USM Process

Contact Info

Product

Resources

About