Optimal FSW Process Parameters to Improve the Strength of Dissimilar AA6061-T6 to Cu Welds with Zn Interlayer

Friction stir welding (FSW) is a solid-state welding technique in which the joint quality was predominantly subjected to heat formation throughout the metal welding process. The weld joint produced from FSW was better than the other fusion welding process. In this research, the base plates AA6101 and C11000 of 5 mm thickness were joined using the hardened oil-hardened nonshrinkable steel(OHNS) tool by the FSW method. The design of experiment (DOE) was used to optimize the input parameters such as tool rotational speed (rpm), feed rate (mm/min), and tool pin offset (mm) on output parameter ultimate tensile strength (UTS). The design of experiment (DOE) was carried out by employing a Taguchi L9 orthogonal array, three factors, and three levels for obtaining a quality joint with good strength. The results of nine trial runs from the Taguchi experimental approach were formulated and analyzed using the statistical tool analysis of variance (ANOVA) using MINITAB 19 software. ANOVA analysis was employed to find the contribution of the input parameters toward the output. The optimized input process parameters will help to create effective weld joints. This study revealed that tool pin offset towards softer metal at medium tool rotational speed would create joints with the highest UTS. Scanning Electron Microscope (SEM) was applied to investigate the structural changes in the FSW of Al-Cu joints.Friction stir welding (FSW) is a solid-state welding technique in which the joint quality was predominantly subjected to heat formation throughout the metal welding process. The weld joint produced from FSW was better than the other fusion welding process. In this research, the base plates AA6101 and C11000 of 5 mm thickness were joined using the hardened oil-hardened nonshrinkable steel(OHNS) tool by the FSW method. The design of experiment (DOE) was used to optimize the input parameters such as tool rotational speed (rpm), feed rate (mm/min), and tool pin offset (mm) on output parameter ultimate tensile strength (UTS). The design of experiment (DOE) was carried out by employing a Taguchi L9 orthogonal array, three factors, and three levels for obtaining a quality joint with good strength. The results of nine trial runs from the Taguchi experimental approach were formulated and analyzed using the statistical tool analysis of variance (ANOVA) using MINITAB 19 software. ANOVA analysis was employed to find the contribution of the input parameters toward the output. The optimized input process parameters will help to create effective weld joints. This study revealed that tool pin offset towards softer metal at medium tool rotational speed would create joints with the highest UTS. Scanning Electron Microscope (SEM) was applied to investigate the structural changes in the FSW of Al-Cu joints.

show abstract

Optimal weld bead profiles in the conduction mode LBW of thin Ti–6Al–4V alloy sheets

Harish¹,

Seeram²,

Goteti

et al. 2021

AIMSMATES

View full text Add to dashboard Cite

<abstract> <p>Day by day laser welding (LW) is gaining industrial importance. Good quality of weld joints can be realized through this process. Because this process yields low distortion and small weld bead. Aerospace, nuclear, automotive, and biomedical industries are opting for the lightweight and corrosion resistance titanium alloys. This paper deals with the generation of optimal weld bead profiles in the conduction mode laser beam welding (LBW) of thin Ti–6Al–4V alloy sheets. Laser beam diameter, power and welding speed are the 3 LBW parameters, whereas, bead width, depth of penetration, heat affected zone and maximum temperature are the performance indicators (PIs). 3 levels are set for each LBW parameter. Taguchi's L<sub>9</sub> OA (orthogonal array) is selected to minimize the numerical simulations. ANSYS Fluent V16.0 with Vc++ code is used to develop a generic model. %Contribution of each process variable on the PIs is assessed performing ANOVA analysis. The range of PIs is assessed adopting the modified Taguchi approach. A set of optimal LBW parameters are identified considering a multi-objective optimization technique. For these optimal LBW parameters weld bead width is minimum, and the depth of penetration is maximum. Empirical relations for PIs are developed and validated with simulations. Utilizing the Taguchi's design of experiments, empirical relations are developed for the performance indicators in laser beam welding (LBW) simulations performing few trial runs and identified the optimal LBW process parameters.</p> </abstract>

show abstract

scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.

Contact Info

hi@scite.ai

10624 S. Eastern Ave., Ste. A-614

Henderson, NV 89052, USA

Blog Terms and Conditions API Terms Privacy Policy Contact Cookie Preferences Do Not Sell or Share My Personal Information

Made with 💙 for researchers

Part of the Research Solutions Family.

Optimal FSW Process Parameters to Improve the Strength of Dissimilar AA6061-T6 to Cu Welds with Zn Interlayer

Cited by 3 publications

References 13 publications

Incorporation of Taguchi approach with CFD simulations on laser welding of spacer grid fuel rod assembly

Incorporation of Taguchi approach with CFD simulations on laser welding of spacer grid fuel rod assembly

Design and Optimization of Friction Stir Welding of Al-Cu BUTT Joint Configuration using Taguchi Method

Optimal weld bead profiles in the conduction mode LBW of thin Ti–6Al–4V alloy sheets

Contact Info

Product

Resources

About