On the origin of cube texture in copper

Duggan, B.J.; Lücke, K.; Köhlhoff, G.; Lee, Chun‐Sing

doi:10.1016/0956-7151(93)90211-a

Cited by 113 publications

(63 citation statements)

References 11 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Both protrusions are located at S oriented deformed matrix. As discussed in earlier work, preferential growth into S orientations may be related to either misorientations near (although not exactly at) 40°<111> [4] or higher stored energy within S oriented bands [49]. If the preferential growth is due to higher stored energy within S oriented bands, it would be expected that twins of the supercube grains would grow equally well into these S oriented bands, which is not observed experimentally for supercube grains in this sample.…”

Section: Misorientationsmentioning

confidence: 78%

“…A small amount of cube texture (~2% volume fraction) is observed, which has been seen in cold-rolled copper [4] and other metals [33,34]. The cube oriented regions are usually observed as thin bands (see Figure 2a).…”

Section: Deformed Microstructure and Texturementioning

confidence: 96%

“…The approach above, however, has the disadvantage of "destroyed evidence" [4]: the deformed matrix favorable for growth has been invaded. This is even more problematic for the present study, because supercube grains can only be distinguished after reaching a certain size, and the growth curves in Figure 10 show that the growth rates are typically highest at the initial growth stage.…”

Section: Misorientationsmentioning

confidence: 99%

“…[2]). Copper is one the most discussed materials, probably because the recrystallization texture in cold-rolled copper seems to be sensitive to the chemical compositions and many processing parameters [3][4][5][6][7][8][9][10][11].…”

Section: Introductionmentioning

confidence: 99%

See 3 more Smart Citations

Supercube grains leading to a strong cube texture and a broad grain size distribution after recrystallization

Lin

Zhang

Pantleon

et al. 2015

Philosophical Magazine

View full text Add to dashboard Cite

2015). Supercube grains leading to a strong cube texture and a broad grain size distribution after recrystallization. Philosophical Magazine, 95(22), 2427-2449. DOI: 10.1080/14786435.2015 AbstractThis work revisits the classical subject of recrystallization of cold-rolled copper. Two characterization techniques are combined: 3-dimensional X-ray diffraction using synchrotron Xrays, which is used to measure the growth kinetics of individual grains in situ, and electron backscatter diffraction, which is used for statistical analysis of the microstructural evolution. As the most striking result, the strong cube texture after recrystallization is found to be related to a few super large cube grains, which were named supercube grains. These few supercube grains become large due to higher growth rates. However, most other cube grains do not grow preferentially. Because of the few supercube grains, the grain size distribution after recrystallization is broad. Reasons for the higher growth rates of supercube grains are discussed, and are related to the local deformed microstructure.

show abstract

Section: Misorientationsmentioning

confidence: 78%

Section: Deformed Microstructure and Texturementioning

confidence: 96%

Section: Misorientationsmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

See 2 more Smart Citations

Supercube grains leading to a strong cube texture and a broad grain size distribution after recrystallization

Lin

Zhang

Pantleon

et al. 2015

Philosophical Magazine

View full text Add to dashboard Cite

show abstract

“…In-situ/ex-situ 2D (x, y, t) characterizations Dynamic studies following in situ or ex situ the boundary migration process are crucial for understanding the migration mechanisms. The direct observations from such studies can avoid the socalled 'destroy-evidence' problem [35], and thus be used to test mechanisms or theories as those obtained based on the 2D post-mortem analysis e.g. those given in section 2.…”

Section: D Characterization Of Recrystallization Boundary Using Fibmentioning

confidence: 99%

Boundary migration during recrystallization: experimental observations

Zhang

Jensen

2015

IOP Conf. Ser.: Mater. Sci. Eng.

View full text Add to dashboard Cite

Study on Fabrication of Ni8W/Ni12W/Ni8W Composite Substrate for Coated Conductors

Suo

Yang

et al. 2020

Adv Eng Mater

View full text Add to dashboard Cite

Three types of Ni8W/Ni12W/Ni8W composite substrates with different layer thickness ratios are thoroughly investigated. A composite substrate with a 1:2:1 thickness ratio is found to be more appropriate for application because of its sharper cube texture, better mechanical strength, and lower magnetization. To overcome cracking and fracture during cold rolling, hot rolling is sometimes conducted before cold rolling. A second step in the annealing process is researched comprehensively to fabricate a 121‐composite substrate with a sharper cube texture. A nearly non‐ferromagnetic 121‐Ni8W/Ni12W/Ni8W composite substrate with a sharp cube texture and strong mechanical strength is successfully fabricated.

show abstract

On the origin of cube texture in copper

Cited by 113 publications

References 11 publications

Supercube grains leading to a strong cube texture and a broad grain size distribution after recrystallization

Supercube grains leading to a strong cube texture and a broad grain size distribution after recrystallization

Boundary migration during recrystallization: experimental observations

Study on Fabrication of Ni8W/Ni12W/Ni8W Composite Substrate for Coated Conductors

Contact Info

Product

Resources

About