New Protection Schemes in Smarter Power Grids With Higher Penetration of Renewable Energy Systems

Dehghanian, Payman; Wang, Bo; Tasdighi, Mohammad

doi:10.1016/b978-0-08-102592-5.00011-9

Cited by 15 publications

(9 citation statements)

References 33 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…PMUs are used to produce synchrophasor measurementsfundamental frequency voltage and current measurements that are time synchronised [54]. Normally, synchophasors are communicated to a central computer, and this information can be used to undertake state estimation, fault detection/location and wide area monitoring, including protection [55]- [57]. While the use of synchrophasors from multiple PMUs can be used to measure line impedance [51], [58], [59], the focus of this article is on the local techniques which utilise local measurements only.…”

Section: ) Local Pmu Derived Observersmentioning

confidence: 99%

Review of Local Network Impedance Estimation Techniques

et al. 2020

View full text Add to dashboard Cite

Section: ) Local Pmu Derived Observersmentioning

confidence: 99%

Review of Local Network Impedance Estimation Techniques

et al. 2020

View full text Add to dashboard Cite

“…where; I A is the local-end current; I B is the remote-end current Power flow is normally unidirectional from the source to consumers [18][19][20] with conventional generators. However, lately there is an overwhelming RE penetration such as solar PV in power system [19][20][21][22].…”

Section: Line Differential Protection Relaymentioning

confidence: 99%

“…As a result, it is a challenge to power system protection since most of the protective relaying design is based on the assumption which is radial in nature. Therefore, due to the impact of RE to power system behavior [17][18][19][20][21][23][24][25], the reliability of differential protection scheme needs be analyzed when the power system network is without and with RE penetration such as solar PV.…”

Section: Line Differential Protection Relaymentioning

confidence: 99%

Analysis on the behavior of line differential protective relaying with solar PV penetration

Yusoff¹,

Hashim²

2020

IJEECS

View full text Add to dashboard Cite

Power System Protection is very important in electrical power system as it minimizes power supply interruption to customers, and also prevents damages to electrical equipment. Lately, renewable energy (RE) penetration in power system helps to support and fulfil the increasing demand of electricity to customers. However, the contribution of power from RE such as solar photovoltaic (PV) will increase the fault level and lead to reverse power flow; thus, it will affect power system protection reliability. This paper focuses on evaluating the reliability of differential protection relay during steady state, internal and external faults conditions when the power system is without and with solar PV penetration. Steady state and three-phase symmetrical line fault will be simulated in IEEE 39 bus test system using Power System Simulation for Engineering (PSS<sup>®</sup>E) software.

show abstract

“…Many researchers have conducted studies on how to maintain the availability of electricity [1,2,3,4]. Likewise, to maintain the system security from various kinds of interference [5,6,7], in order that the sustainability of electricity supply to consumers can be enhanced. To increase the consumers' electricity supply, the producers are required to add the power supply to the system.…”

Section: Introductionmentioning

confidence: 99%

Effects of the Temperature on the Output Voltage of Mono-Crystalline and Poly-Crystalline Solar Panels

Eteruddin

Atmam

Setiawan

et al. 2019

Sinergi

View full text Add to dashboard Cite

People can make solar energy alternative energy by employing solar panels to generate electricity. The utilization of solar energy on a solar panel to generate electricity is affected by the weather and the duration of the radiation, and they will affect the solar panel’s temperature. There are various types of solar panels that can be found on the market today, including Mono-Crystalline and Poly-Crystalline. The difference in the material used needs to be observed in terms of temperature changes in the solar module. Our study’s findings showed that a change in the temperature would impact the solar panel’s output voltage, and the solar panel’s output voltage would change when it was connected to the load although the measured temperatures were almost the same.

show abstract

New Protection Schemes in Smarter Power Grids With Higher Penetration of Renewable Energy Systems

Cited by 15 publications

References 33 publications

Review of Local Network Impedance Estimation Techniques

Review of Local Network Impedance Estimation Techniques

Analysis on the behavior of line differential protective relaying with solar PV penetration

Effects of the Temperature on the Output Voltage of Mono-Crystalline and Poly-Crystalline Solar Panels

Contact Info

Product

Resources

About