New Multi-Scale Hybrid System Based on Maple Wood Flour and Nano Crystalline Cellulose: Morphological, Mechanical and Physical Study

Yousefian, Hajar; Azouz, Kaouther; Rodrigue, Denis

doi:10.1007/s10924-016-0752-0

Cited by 10 publications

(10 citation statements)

References 32 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…reinforcement, the tensile moduli increased for S30L75T by 33% compared to S30L0T. The same trend was observed by Kakroodi et al and Yousefian et al .…”

Section: Resultssupporting

confidence: 87%

Rotational molding of self‐hybrid composites based on linear low‐density polyethylene and maple fibers

Hanana

Rodrigue

2017

Polymer Composites

Self Cite

View full text Add to dashboard Cite

In this study, the morphological, physical, and mechanical properties of maple fiber self‐hybrid composites reinforced linear low‐density polyethylene (LLDPE) have been investigated for different concentration (10, 20, and 30%) and ratio (100/0, 75/25, 50/50, 25/75, and 0/100) of short (125–250 μm), medium (250–355 μm), and long (355–500 μm) fibers. Maple surface treatment with a coupling agent (maleated polyethylene, MAPE) was also investigated. The results show that surface treatment increased the tensile modulus and strength, and impact strength. Finally, the self‐hybrid composites gave better properties than single size fibers since a positive deviation from the linear law of mixture was observed, especially at 20% wt. For example, a 75/25 ratio of medium/short or long/short fibers produced a tensile modulus and tensile strength between 13% and 33% higher than composites formulated with a single fiber size. POLYM. COMPOS., 39:4094–4103, 2018. © 2017 Society of Plastics Engineers

show abstract

“…reinforcement, the tensile moduli increased for S30L75T by 33% compared to S30L0T. The same trend was observed by Kakroodi et al and Yousefian et al .…”

Section: Resultssupporting

confidence: 87%

Rotational molding of self‐hybrid composites based on linear low‐density polyethylene and maple fibers

Hanana

Rodrigue

2017

Polymer Composites

Self Cite

View full text Add to dashboard Cite

show abstract

“…with a 42% increase compared with neat LLDPE (617 MPa). This significant increase is associated with the presence of rigid particles in the polymer matrix increasing the overall stiffness of the composite because maple fibres have a higher modulus (10–13 GPa) than the matrix 16,33 . This is especially true for the top part of the sample, being in compression.…”

Section: Resultsmentioning

confidence: 99%

“…This higher increase can be attributed to good interfacial bonding between the fibres and the matrix making more efficient all the reinforcement; i.e. the top part in compression and the bottom part in tension 33 .…”

Section: Resultsmentioning

confidence: 99%

Morphology and Mechanical Properties of Maple Reinforced LLDPE Produced by Rotational Moulding: Effect of Fibre Content and Surface Treatment

Hanana

Chimeni

Rodrigue

2018

Polymers and Polymer Composites

Self Cite

View full text Add to dashboard Cite

In this study, wood-plastic composites (WPC) were produced by rotomoulding, to study the effect of fibre content and surface treatment on their properties. Maple wood fibre, with or without surface treatment with maleated polyethylene (MAPE), was used to improve the mechanical properties of linear low-density polyethylene (LLDPE). From the composites produced, a complete morphological and mechanical characterisation was performed. The results showed that MAPE surface treatment improved the fibre-matrix interface quality and the mechanical properties (56% increase in tensile modulus and 60% increase in flexural modulus over the neat matrix with 19% in impact strength with respect to untreated fibres) at 30% wt.

show abstract

“…The final properties of hybrid composites depend are function of different factors [53,74,104,120], and Table 4 summarizes some of the most important mechanical and thermal properties of hybrid composites based on thermoset matrices. The effect of fiber and matrix type, as well as fiber surface treatment is reported with their mechanical properties and thermal degradation temperature.…”

Section: Hybrid Compositesmentioning

confidence: 99%

Production and Characterization of Hybrid Polymer Composites Based on Natural Fibers

Rodriguez‐Castellanos¹,

Rodrigue²

2016

Composites From Renewable and Sustainable Materials

Self Cite

View full text Add to dashboard Cite

In this chapter, a review is made on the processing and properties of hybrid composites based on a polymer matrix and a blend of diferent natural (lignocellulosic) ibers. In particular, the processing methods are described and comparisons are made between the general properties with a focus on physical, mechanical and thermal properties. A discussion is presented on the efect of the polymer and iber types, as well as reinforcement content. Properties improvement is also discussed using iber surface treatment or the addition of coupling agents. Finally, auto-hybrid composites are presented with conditions leading to a positive deviation from the rule of hybrid mixture (RoHM) model.

show abstract

New Multi-Scale Hybrid System Based on Maple Wood Flour and Nano Crystalline Cellulose: Morphological, Mechanical and Physical Study

Cited by 10 publications

References 32 publications

Rotational molding of self‐hybrid composites based on linear low‐density polyethylene and maple fibers

Rotational molding of self‐hybrid composites based on linear low‐density polyethylene and maple fibers

Morphology and Mechanical Properties of Maple Reinforced LLDPE Produced by Rotational Moulding: Effect of Fibre Content and Surface Treatment

Production and Characterization of Hybrid Polymer Composites Based on Natural Fibers

Contact Info

Product

Resources

About