Nano-ZrO2 filled high-density polyethylene composites: Structure, thermal properties, and the influence γ-irradiation

Nabiyev, A.A.; Olejniczak, Andrzej; Pawlukojć, A.; Bǎlǎșoiu, M.; Bunoiu, Mădălin; Maharramov, Abel; Nuriyev, M. A.; Ismayilova, R. S.; Azhibekov, A. K.; Kabyshev, A. M.; Ivankov, Oleksandr I.; Vlase, Gabriela; Linnik, Dmitriy; Shukurova, A. A.; Ivanshina, Olga Yu.; Турченко, В. А.; Куклин, А. И.

doi:10.1016/j.polymdegradstab.2019.109042

Cited by 23 publications

(7 citation statements)

References 42 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…High energy ionizing radiation such as proton, 13 gammaray, [14][15][16][17][18][19][20] UV treatment, [21][22][23][24][25] and X-ray 15 has been utilized as an alternative approach for tailoring the structural and electrical conductivities of the lms. Usually, these approaches are temperature independent and in turn results in material with higher purity.…”

Section: Introductionmentioning

confidence: 99%

Consequences of gamma-ray irradiation on structural and electronic properties of PEDOT:PSS polymer in air and vacuum environments

et al. 2021

View full text Add to dashboard Cite

show abstract

Section: Introductionmentioning

confidence: 99%

Consequences of gamma-ray irradiation on structural and electronic properties of PEDOT:PSS polymer in air and vacuum environments

et al. 2021

View full text Add to dashboard Cite

show abstract

“…The UHMWPE‐ZrO 2 composites showed similar reduced oxidation index which attributed to improved crystallinity of composites relative to neat UHMWPE 183 . Nano ZrO 2 reinforced HDPE was studied by Nabiyev et al 221 The small angle neutron scattering (SANS) result confirmed the well dispersion of ZrO 2 in HDPE and the gamma‐irradiation leads to no change in filler‐polymer interface 221 …”

Section: Effect Of Gamma‐irradiation On Wear Resistance Of Carbonaceous/noncarbonaceous Based Uhmwpe Composites/nanocompositesmentioning

confidence: 96%

Effects of reinforcements and gamma‐irradiation on wear performance of ultra‐high molecular weight polyethylene as acetabular cup liner in hip‐joint arthroplasty: A review

Nayak

Balani

2021

J of Applied Polymer Sci

View full text Add to dashboard Cite

Improving the wear resistance of ultra‐high molecular weight polyethylene (UHMWPE), the gold standard polymer for acetabular component in hip joint arthroplasty, is the most important challenge in joint arthroplasty. The possible ways that have been approached to this challenge are by: (i) engineering multi‐phase that is, both carbonaceous and noncarbonaceous fillers‐based polyethylene composites, which unite the inherent attributes of each element available in the system. The wear rate of carbonaceous composite is nearly 50% lower (5.11–6.69 × 10−5 mm3/Nm) than that of noncarbonaceous composite (10–12.5 × 10−5 mm3/Nm), thus, recognized as a potential reinforcement, and (ii) coupling gamma‐irradiation, which is a mandated sterilization process, with multi‐phase nanocomposite to understand the free radical‐scavenging effect of fillers and improved interfacial adhesion strength between fillers and matrix. After the exposure of gamma‐rays (50–100 kGy), the free radicals formed by bond breakage in both the reinforcements and the matrix recombine to form covalent/Van der Waals bond in the interface. Thus, dramatical improvement in wear resistance of both types of composites with 2–4 times decreased wear rate is observed compared to that of composites under un‐irradiated condition. However, enhancing the interfacial adhesion between two different phases is a major constraint in the design of UHMWPE composites. Many methods such as functionalization of reinforcements, and irradiation on functionalized UHMWPE composites that can be approached to address this constraint are documented in this review.

show abstract

“…The most prominent peaks, due to the crystalline phase, are at 1063, 1130, 1295, and 1416 cm −1 . For nanocomposite films, the relative intensity of the signals due to the amorphous phase does not change with the addition of nano-ZrO 2 [60].…”

Section: Effect Of Filler Type and Concentration On The Crystallinity Of The Hdpe Matrixmentioning

confidence: 96%

Composite Films of HDPE with SiO2 and ZrO2 Nanoparticles: The Structure and Interfacial Effects

et al. 2021

Self Cite

View full text Add to dashboard Cite

Herein, we investigated the influence of two types of nanoparticle fillers, i.e., amorphous SiO2 and crystalline ZrO2, on the structural properties of their nanocomposites with high-density polyethylene (HDPE). The composite films were prepared by melt-blending with a filler content that varied from 1% to 20% v/v. The composites were characterized by small- and wide-angle x-ray scattering (SAXS and WAXS), small-angle neutron scattering (SANS), Raman spectroscopy, differential scanning calorimetry (DSC), and scanning electron microscopy (SEM). For both fillers, the nanoaggregates were evenly distributed in the polymer matrix and their initial state in the powders determined their surface roughness and fractal character. In the case of the nano-ZrO2 filler, the lamellar thickness and crystallinity degree remain unchanged over a broad range of filler concentrations. SANS and SEM investigation showed poor interfacial adhesion and the presence of voids in the interfacial region. Temperature-programmed SANS investigations showed that at elevated temperatures, these voids become filled due to the flipping motions of polymer chains. The effect was accompanied by a partial aggregation of the filler. For nano-SiO2 filler, the lamellar thickness and the degree of crystallinity increased with increasing the filler loading. SAXS measurements show that the ordering of the lamellae is disrupted even at a filler content of only a few percent. SEM images confirmed good interfacial adhesion and integrity of the SiO2/HDPE composite. This markedly different impact of both fillers on the composite structure is discussed in terms of nanoparticle surface properties and their affinity to the HDPE matrix.

show abstract

Nano-ZrO2 filled high-density polyethylene composites: Structure, thermal properties, and the influence γ-irradiation

Cited by 23 publications

References 42 publications

Consequences of gamma-ray irradiation on structural and electronic properties of PEDOT:PSS polymer in air and vacuum environments

Consequences of gamma-ray irradiation on structural and electronic properties of PEDOT:PSS polymer in air and vacuum environments

Effects of reinforcements and gamma‐irradiation on wear performance of ultra‐high molecular weight polyethylene as acetabular cup liner in hip‐joint arthroplasty: A review

Composite Films of HDPE with SiO2 and ZrO2 Nanoparticles: The Structure and Interfacial Effects

Contact Info

Product

Resources

About