Multibolted Joints for GFRP Structural Members

Hassan, Nahla K.; Mohamedien, Mohamed A.; Rizkalla, Sami

doi:10.1061/(asce)1090-0268(1997)1:1(3)

Cited by 34 publications

(29 citation statements)

References 2 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Hassan (1995) (also in Hassan et al, 1997) measured the strength of 105 multi-bolted connections using the same test procedure as Rosner (1992) for the characterization of 102 single bolted connections (also in Rosner and Rizkalla, 1995). There was, again, no specimen repetition.…”

Section: Model Verification and Discussionmentioning

confidence: 99%

“…Because of the different pultruded flat sheets in the Hassan (995) Presented in Tables 4 and 5 are the 17 net-tension test results from Hassan et al (1997) for the modeling configuration in Figure 4, and to which Equation (6) can be used to predict the net-tension strength from a knowledge of the geometry (w, e 1 , t and s), the filled-and open-hole correlation coefficients and the tensile strengths of the material. In column (1) the test label is given.…”

Section: Model Verification and Discussionmentioning

confidence: 99%

“…Column (9) gives, J. T. MOTTRAM, 'Prediction of net-tension strength for multi-row bolted connections of pultruded material using the Hart-Smith semi-empirical modeling approach,' Journal of Composites for Construction, 14 1, (2010), 105-114. ISSN 1090 for each specimen, the ultimate tensile load (R nt,f,exp ) measured using the test methodology described in Hassan et al (1997). This failure load, in kN, is for one of the two outer plates, and it is assumed that both plates take an equal share of the tension loading.…”

Section: Model Verification and Discussionmentioning

confidence: 99%

“…Test label (Hassan et al 1997) Orientation of pultrusion to tension load,  Thickness, (Hassan et al 1997) R nt,f,theory from Equation (6) [a] (kN) R nt,f,exp /R t,nf,theory (9)/(10)  in Figure 5 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) 0A2 0 12.7 Table 5. Comparison of predicted and experimental strengths for 90 o bolted connections with two rows of a centrally placed bolt.…”

mentioning

confidence: 99%

See 3 more Smart Citations

Prediction of Net-Tension Strength for Multirow Bolted Connections of Pultruded Material Using the Hart-Smith Semiempirical Modeling Approach

Mottram

2010

J. Compos. Constr.

View full text Add to dashboard Cite

Presented in this paper is a study to show that the Hart-Smith semi-empirical modeling approach can be used to predict the net-tension strength of multi-rowed experimental-to-theory strength ratios are < 1.0, and only one of these two could be said to have predicted unsafe net-tension strengths. With none of the ratios exceeding 1.2, it is seen that the simple and versatile modeling approach gives very acceptable predictions. To determine the modeling parameters that will enable the Hart-Smith approach to be in a LRFD design standard there is a need for a comprehensive series of strength tests, for net-tension failure with filled-and open-holes, that covers the complete range of multi-rowed bolted connections that is to be permitted by the standard.

show abstract

Section: Model Verification and Discussionmentioning

confidence: 99%

Section: Model Verification and Discussionmentioning

confidence: 99%

Section: Model Verification and Discussionmentioning

confidence: 99%

mentioning

confidence: 99%

See 2 more Smart Citations

Prediction of Net-Tension Strength for Multirow Bolted Connections of Pultruded Material Using the Hart-Smith Semiempirical Modeling Approach

Mottram

2010

J. Compos. Constr.

View full text Add to dashboard Cite

show abstract

“…However, a severe stress concentration occurs at holes of the connection, which reduces the total efficiency of the connection. The efficiency depends on failure mode of the connection 1) .…”

Section: Introductionmentioning

confidence: 99%

Effects of Cover Plate Stiffness on Load Distribution of Bearing-Type Multi-Row Bolted Connections for FRP Composite Structures

Kader

Kitane

Itoh

2015

J. Soc. Mat. Sci., Japan

View full text Add to dashboard Cite

The present study investigates the effect of different thicknesses of steel and fiber reinforced polymer (FRP) cover plates on the mechanical behavior of bearing-type multi-row bolted connections for FRP composite structures. Connections with a double-lap configuration up to four rows of bolts subjected to tensile loads have been studied numerically. These numerical data are examined in detail to understand the effects of cover plate stiffness on load distributions among rows of bolts. The study also considers the influence of geometric parameters on the load distributions. For validation of the connection model, numerical results are compared with experimental results available in literature. The results show that the load distribution in bearing-type multi-row bolted connections is significantly affected by the cover plate stiffness. A connection with higher cover plate stiffness tends to show lower efficiency. For a connection with steel cover plates, to increase number of bolt rows more than three does not lead to a higher capacity of a connection. The results also indicate that effect of geometric parameters on the load distribution is not significant with change of cover plate stiffness.

show abstract

Bolted connections in PFRP structures

Turvey

2000

Prog. Struct. Engng Mater.

View full text Add to dashboard Cite

A brief overview of some of the more noteworthy PFRP structures is presented. It is noted that, at the present stage of development, bolted connections are used extensively in fabricating structural frames from PFRP sections. Tests on bolted connections between PFRP sections, i.e., axially loaded and moment connections, and guidance for their design are reviewed. Some areas where further research and guidance are needed are mentioned and the paper is concluded with a few remarks on possible future developments.

show abstract

Multibolted Joints for GFRP Structural Members

Cited by 34 publications

References 2 publications

Prediction of Net-Tension Strength for Multirow Bolted Connections of Pultruded Material Using the Hart-Smith Semiempirical Modeling Approach

Prediction of Net-Tension Strength for Multirow Bolted Connections of Pultruded Material Using the Hart-Smith Semiempirical Modeling Approach

Effects of Cover Plate Stiffness on Load Distribution of Bearing-Type Multi-Row Bolted Connections for FRP Composite Structures

Bolted connections in PFRP structures

Contact Info

Product

Resources

About