Search citation statements
Paper Sections
Citation Types
Year Published
Publication Types
Relationship
Authors
Journals
One of the largest clastic reservoir fields in the Sultanate of Oman has been discovered in 1980 and put on production in 1985. The field produces viscous oil, ranging from 200 - 2000+ cP at reservoir conditions. Over 75% of the wells drilled are horizontal wells and the field is one of the largest producers in the Sultanate of Oman. The field challenges include strong aquifer, high permeability zones/faults. Due to large fluid mobility contrast, the fields have experienced in pre-mature water breakthrough that has resulted in very high-water cuts. The average field water cut for open hole horizontal well after 6-9 months of production is over 94%. This paper details a meticulous journey in qualification, field trials followed by field-wide implementation and performance evaluation of Autonomous Inflow Control Valve (AICV) technology in reducing water production and increasing oil production significantly. AICV can precisely identify the fluid flowing through it and shutting-off the high water or gas saturated zones while producing oil from healthy oil-saturated zones. Like other AICDs (Autonomous Inflow Control Device) AICV can differentiate the fluid flowing through it via fluid properties such as viscosity and density at reservoir conditions. However, AICV's performance is superior due to its advanced design based on both Hagen-Poiseuille and Bernoulli's principles. This paper describes a comprehensive AICV completion design workflow that was developed across a multi-disciplinary team. Some of the initial wells completed with AICV has shown the benefit of accelerating oil production of over 30,000 bbls within the first few months of installation. Many wells started with 5-10 % water cut and are still producing with low water cut and higher oil production. The operator has approved AICV technology based on techno-commercial analysis and its positive impact on the project such as accelerated oil production and lower cost of water handling at the surface. AICV also helped in mitigating the facility constraints of handling produced water which resulted in reduce OPEX as allow the operator continued to drill horizontal wells. At the time of writing this paper, the operator has completed several dozen wells in the field with AICV technology and has an aggressive long term plan to complete several new and old wells. Finally, this paper also discusses in detail the comparative analysis of AICV wells for different subsurface conditions and share some lessons learned to further optimise the well performance. The technology has a profound impact on improved sweep efficiency and as well plays an instrumental role in reducing the carbon footprint by reducing the significant water production at the surface. It is concluded that AICV is a cost-effective field-proven technology for the water shut-off application. Due to its ability to autonomously identify and shut off water and gas production, the AICV technology has been approved to use as full fields implementation and in other fields. Field Background and Reservoir/Production challenges The operator produces around nine barrels of water against each produced barrel of oil. In general, the water produces to the surface with hydrocarbons contains many chemicals, which are usually not environmentally friendly and required additional treatment which increases the disposal cost. The Operator was looking for a cost-effective and proven technology that can control/shut off water production and improve oil production. The fields have a strong bottom aquifer and heterogeneous reservoir properties, such as permeability and downhole water saturation profiles. The challenge with matured brownfields, typically newly drilled wells will have pre-mature water breakthrough within few months of production. The fields have a highly viscous oil, with viscosity ranges from 200 cP up to 2000 cp at downhole conditions, thus creating a high mobility contrast between the oil and water, causing water fingering and coning at an early stage of production. These production challenges cause a significant recoverable oil left in the reservoir i.e. bypassed oil. Furthermore, excessive surface water production affects the integrated production system back pressures and flow, as well as an individual well's dynamics and pump efficiencies. This also has a significant downstream impact, where substantial investment is needed to handle, treat, and dispose of the water. Reducing these water volumes at the surface adds up to a tangible reduction in OPEX for water processing as well as environmentally friendly and assist the reservoir to maintain the reservoir pressure and energy by keeping the water in the reservoir. (Hilal et al 1997, Hassasi et al 2020)
One of the largest clastic reservoir fields in the Sultanate of Oman has been discovered in 1980 and put on production in 1985. The field produces viscous oil, ranging from 200 - 2000+ cP at reservoir conditions. Over 75% of the wells drilled are horizontal wells and the field is one of the largest producers in the Sultanate of Oman. The field challenges include strong aquifer, high permeability zones/faults. Due to large fluid mobility contrast, the fields have experienced in pre-mature water breakthrough that has resulted in very high-water cuts. The average field water cut for open hole horizontal well after 6-9 months of production is over 94%. This paper details a meticulous journey in qualification, field trials followed by field-wide implementation and performance evaluation of Autonomous Inflow Control Valve (AICV) technology in reducing water production and increasing oil production significantly. AICV can precisely identify the fluid flowing through it and shutting-off the high water or gas saturated zones while producing oil from healthy oil-saturated zones. Like other AICDs (Autonomous Inflow Control Device) AICV can differentiate the fluid flowing through it via fluid properties such as viscosity and density at reservoir conditions. However, AICV's performance is superior due to its advanced design based on both Hagen-Poiseuille and Bernoulli's principles. This paper describes a comprehensive AICV completion design workflow that was developed across a multi-disciplinary team. Some of the initial wells completed with AICV has shown the benefit of accelerating oil production of over 30,000 bbls within the first few months of installation. Many wells started with 5-10 % water cut and are still producing with low water cut and higher oil production. The operator has approved AICV technology based on techno-commercial analysis and its positive impact on the project such as accelerated oil production and lower cost of water handling at the surface. AICV also helped in mitigating the facility constraints of handling produced water which resulted in reduce OPEX as allow the operator continued to drill horizontal wells. At the time of writing this paper, the operator has completed several dozen wells in the field with AICV technology and has an aggressive long term plan to complete several new and old wells. Finally, this paper also discusses in detail the comparative analysis of AICV wells for different subsurface conditions and share some lessons learned to further optimise the well performance. The technology has a profound impact on improved sweep efficiency and as well plays an instrumental role in reducing the carbon footprint by reducing the significant water production at the surface. It is concluded that AICV is a cost-effective field-proven technology for the water shut-off application. Due to its ability to autonomously identify and shut off water and gas production, the AICV technology has been approved to use as full fields implementation and in other fields. Field Background and Reservoir/Production challenges The operator produces around nine barrels of water against each produced barrel of oil. In general, the water produces to the surface with hydrocarbons contains many chemicals, which are usually not environmentally friendly and required additional treatment which increases the disposal cost. The Operator was looking for a cost-effective and proven technology that can control/shut off water production and improve oil production. The fields have a strong bottom aquifer and heterogeneous reservoir properties, such as permeability and downhole water saturation profiles. The challenge with matured brownfields, typically newly drilled wells will have pre-mature water breakthrough within few months of production. The fields have a highly viscous oil, with viscosity ranges from 200 cP up to 2000 cp at downhole conditions, thus creating a high mobility contrast between the oil and water, causing water fingering and coning at an early stage of production. These production challenges cause a significant recoverable oil left in the reservoir i.e. bypassed oil. Furthermore, excessive surface water production affects the integrated production system back pressures and flow, as well as an individual well's dynamics and pump efficiencies. This also has a significant downstream impact, where substantial investment is needed to handle, treat, and dispose of the water. Reducing these water volumes at the surface adds up to a tangible reduction in OPEX for water processing as well as environmentally friendly and assist the reservoir to maintain the reservoir pressure and energy by keeping the water in the reservoir. (Hilal et al 1997, Hassasi et al 2020)
One of the largest operators in the Sultanate of Oman discovered a clastic reservoir field in 1980 and put it on production in 1985. The field produces viscous oil, ranging from 200 - 2000+ cP at reservoir conditions. Over 75% of the wells drilled are horizontal wells and the field is one of the largest producers in the Sultanate of Oman. The field challenges include strong aquifer, high permeability zones/faults and large fluid mobility contrast have resulted that most of the wells started with very high-water cuts. The current field water cut is over 94%. This paper details operator's meticulous journey in qualification, field trials followed by field-wide implementation and performance evaluation of Autonomous Inflow Control Valve (AICV) technology in reducing water production and increasing oil production significantly. AICV can precisely identify the fluid flowing through it and shutting-off the high water or gas saturated zones autonomously while stimulating oil production from healthy oil-saturated zones. Like other AICDs (Autonomous Inflow Control Device) AICV can differentiate the fluid flowing through it via fluid properties such as viscosity and density at reservoir conditions. However, AICVs performance is superior due to its advanced design based on Hagen-Poiseuille and Bernoulli's principles. This paper describes an AICV completion design workflow involving a multi-disciplinary team as well as some of the field evaluation criteria to evaluate AICV well performance in the existing and in the new wells. The operator has completed several dozens of production wells with AICV technology in the field since 2018-19. Based on the field performance review, it has shown the benefit of accelerating oil production as well as reduction of unwanted water which not only reduces the OPEX of these wells but at the same time enormous positive impact on the environment. Many AICV wells started with just 25-40 % water cut and are still producing with low water cut and higher oil production. Based on the initial field-wide assessment, it is also envisaged that AICV wells will assist in achieving higher field recovery. Also, AICV helped in mitigating the facility constraints of handling produced water which will allow the operator continued to drill in-fill horizontal wells. Finally, the paper also discusses in detail the long-term performance results of some of the wells and their impact on cumulative field recovery as well as lessons learned to further optimise the well performance. The technology has a profound impact on improved sweep efficiency and as well plays an instrumental role in reducing the carbon footprint by reducing the significant water production at the surface. It is concluded that AICV technology has extended the field and wells life and proved to be the most cost-effective field-proven technology for the water shut-off application.
Growing energy demand heightened by climate change challenges has seen the oil and gas industry tightly embrace smarter and more sustainable technologies. The motivation is to quickly grasp net-zero targets, while safely optimising oil-gas production. By its nature, the industry has the ingenuity to eliminate unnecessary carbon emissions. However, traditional development plans relied on the use of wells with minimal or no emphasis on the well completion in terms of optimum deliverability. This would produce a mixture of oil and excessive unwanted fluids such as water and/or gas which requires costly energy-intensive processes. Although the process has been optimized to some extent and often re-injects these unwanted fluids back to the reservoir, there has been not enough attention to the environmental impacts as these repetitive treatment processes of the fluids results in discharging excessive and unnecessary Greenhouse Gas (GHG) into the atmosphere. The issue is now widely recognized to be one of the industry challenges in its drive toward net-zero energy delivery. A case study of a heavy crude oil field with a strong water drive, located in a natural reserve in the Marañon basin of the Peruvian Amazon is presented. Here, the implementation of autonomous inflow control devices (AICDs) technology, through a knowledge management process, has made it possible to significantly reduce the volumes of water produced, which are reinjected again, thus generating significant savings in fluid lifting, treatment and energy consumption associated with the operations in this field. The study introduces a workflow that uses a publicly available GHG footprint estimator to evaluate the carbon intensity of different oil and gas field development plans. The estimator predicts the amount of GHG emitted from any individual operation, process and treatment involved in a field development from exploration to delivery at the gate of a refinery. Having this calculation enables the operators to recognize the major GHG emitter operations and optimise the process toward net zero using new technologies, methods and/or workflows. The workflow has then been applied to the field located in the Peruvian Amazon to illustrate the significant impact of flow control technologies on the reduction of GHG emissions and achieving net-zero targets. For example, the amounts of carbon intensity, GHG emission and energy consumption from the field have been estimated to been reduced by up to 56%, 64% and 78% respectively with AICD completions compared to a case of non-AICD completion such as stand-alone screen (SAS) was installed in the wells instead. This study provides the engineers with a workflow to quantify the impacts of the use of new technologies especially flow control devices. It also illustrates the significant role of flow control technologies in achieving net-zero production.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.